background image

9

CROSSOVER CONTROLS: CH 1/2, CH 3/4, X-OVER OUT

As seen in the above drawing, the function of the crossover controls (from
left to right) are as follows:

GAIN

This control matches the output voltage of the source unit or processor to the
amplifier inputs. Rotating this control to the “MIN” mark (counterclockwise)
configures your D7 amplifier to accept input voltages as high as 12V RMS with
the -12dB button pushed “IN” (see “RCA INPUT” drawing on page 12). This
control should be set as low as possible. The basic procedure for setting
input gains is as follows:

1.

Adjust all amplifier gain controls to just above the minimum setting
(fully counterclockwise). If your source unit output voltage is 

less 

than

6 Volts RMS, push the –12dB button for the selected channel pair to
the “OUT” position. If the available signal voltage is 

more 

than 6 Volts

RMS, push the -12dB button to the “IN” position.

2.

Using the highest quality source (usually CD) play some music and
slowly turn up the source unit until you can hear distortion. Now turn
down the volume until the distortion stops. This is your maximum
source unit level.

3.

Turn up the amplifier gain until audible distortion starts. Turn down
the gain to the point JUST BELOW the start of the distortion.

4.

Repeat step 3 for all amplifiers in your system.

Please refer to the Diamond Audio Level Setting Technical Brief available from
the Tech Department for a comprehensive level setting procedure.

Note: To set crossovers, first remove the two 1/16” Allen screws holding

down the security cover using the Allen key provided. When reinstalling
the cover be careful not to overtighten the screws. Damage to the cover
may result.

12

RCA INPUTS AND OUTPUTS

As seen in the above drawing, the function of the RCA inputs, outputs,
and feature buttons are as follows:

CH 1/2 INPUT

The RCA cables from your source unit should be inserted here.

-12dB BUTTON: CH 1/2

To the right of the CH 1/2 INPUT RCAs you will find the -12dB button.
Pushing this button: “IN” allows your amplifier to accept signal voltages as
high as 12VRMS. Pushing this button “OUT” configures the amplifier to
accept signal voltages up to 6VRMS.

-12dB BUTTON: CH 3/4

Works the same as above, but for the CH 3/4 INPUT RCAs.

CH 3/4 INPUT

Additional RCA cables from your source unit should be inserted here.

CH 3/4 INPUT SELECT

Pushing this button “IN” allows signals from CH 1/2 to be sent to both
CH 1/2 and CH 3/4 INPUTS allowing use of a single pair of RCA cables for
all inputs (see block diagram page 16).

X-OVER INPUT SELECT

Pushing this button “IN” routes signals from the CH 1/2 INPUTS to the inputs
of the AUXILIARY X-OVER. Pushing this button “OUT” combines the signals
from CH 1/2 and CH 3/4 (useful for systems requiring non-fading bass).

X-OVER OUT

These RCA outputs are used to provide filtered or unfiltered signals to an
outboard processor or amplifier.

By pushing the X-OVER INPUT SELECT button to the “IN” position,
and pushing the LOWPASS ON/OFF and HIGHPASS ON/OFF crossover
buttons to the “OUT” position, signals available at the CH 1/2 INPUTS will
bypass the crossover and be made available at the X-OVER OUTPUT RCAs
allowing you to “daisy-chain” multiple D7 amplifiers for the ultimate in
system design flexibility.

Summary of Contents for D7054











Reviews: