Diamond Audio Technology D6 300.4 Owner'S Manual Download Page 2

Page: 2 / 12

SPECIAL THANKS

Thank you for choosing a Diamond Audio D6 reference amplifier. The team here at

Diamond insists that you listen to music as the artist intended, and that's what drives us

to develop and engineer cutting edge audio solutions that are true to any audiophiles

guidelines. Each of Diamonds products are concepted, designed, engineered, tested and

sold by pure audio fanatics. Each one of us on the Diamond team realizes how important

audio performance is to you, because it is equally important to us. So rest assured that

you have purchased an amplifier that truly has no competition.

Thanks Again,

The Diamond Team

CAUTION

Prolonged exposure to sound pressure levels in excess of 100 dB can cause permanent

hearing loss. Diamond Audio D6 amplifiers produce enough power to make most speaker

systems exceed that level. Please exercise restraint and protection during their operation

in order to preserve your ability to enjoy their fidelity for years to come.

CONTENTS

Page 3

- Specifications & RMS Power

Page 4

- Physical Dimensions & Appearance/Features

Page 5

- Professional Installation & Mounting

Page 6

- DC Connections

Page 7

- DC Connections

Power and Ground

Page 8

- DC Connections

Amp Current Draw

Page 9

- DC Connections & Speaker Connections

Turn-on (Remote)

Page 10

- D6 300.4/600.4

Bridging, RCA, Crossovers

Page 11

- D6 300.4/600.4

Crossovers (cont), Gain, Aux. Output, Ch 3/4 Input

Page 12

- D6 300.4/600.4

Gain Bypass, Ch 3/4 Mono, Highpass, Lowpass

Page 13

- D6 300.4/600.4

Crossover Freq. Diagrams

Page 14

- D6 1000.1/1500.1

Remote Gain, Speaker Outputs, RCA

Page 15

- D6 1000.1/1500.1

Crossovers, Gain, Subsonic

Page 16

- D6 1000.1/1500.1

Master/Slave, Phase, Lowpass, Crossover Freq. Diagrams

Page 17

- D6 5.2

Bridging, RCA

Page 18

- D6 5.2

Crossovers, Gain, Gain Bypass

Page 19

- D6 5.2

Highpass, Slave, Subsonic, Lowpass, Sub Inversion

Page 20

- D6 5.2

Crossover Freq. Diagrams

Page 21

- Troubleshooting

Page 22

- System Notes

Summary of Contents for D6 300.4













Search results

Summary of Contents for D6 300.4

Reviews:

Related manuals for D6 300.4

Brands by name

Popular brands

Diamond Audio Technology D6 300.4, Owner'S Manual

Search results

Summary of Contents for D6 300.4

Reviews:

Related manuals for D6 300.4

Brands by name

Popular brands