background image

©007 Diamond Audio Technologies, LLC

D3 COMPONENT SPEAKER SYSTEMS

Parts List - D342, D352, and D362

 

(2) D3 Mid-Bass Speakers

 

(2) D3 Grills w/ Mounting Rings

 

(2) Mounting Gaskets

 

(2) D3 12dB Crossovers

 

(2) D3 Tweeters in Flush Mount Cups

 

(2) D3 Tweeter Surface Mounting Cups

 

(1) Mid-Bass Mounting Hardware Kit

 

(1) Tweeter Mounting Hardware Kit

Tweeter Mounting

When flush or surface mounting tweeters, make 
sure desired location can accommodate the 
hole sizes and depth required. Mount cup using 
provided hardware, flush mount illustration shown 
on right. Mount surface cup at desired angle with 
provided screws in tweeter mounting kit. Snake 
speaker wires through tweeter cup, connect tweeter to wires, and snap tweeter into cup by aligning 
the notches. Be careful not to push on the center of the tweeter grill.

Crossover Programming

Each D3 component set comes with a pair of model specific programmable crossovers. Under the clear 
cover there are two jumpers, one marked “TWEETER” and one marked “AXIS”. -2 dB tweeter attenua-
tion can be achieved by moving the “TWEETER” jumper to the -2dB position. The default “reference” 
position has no attenuation effect on the tweeter or is 0dB. The “AXIS” jumper swaps the tweeter 
phase 180 degrees. The default position is “off axis” for mounting in dash boards, doors, and a-pillars. 
The “on axis” position is for tweeter positions that fire directly at the listening area like in custom 
kick pods.

RAF Outputs

Each D3 Component crossover has a third set of outputs marked “RAF”. This stands for Rear Acoustic 
Fill. This output can be used to power an additional speaker off the same channel without affecting 
the impedance load on the source unit. This output allows 15-20% of the total power to the extra 
speaker and is unfiltered or full range.

Summary of Contents for D342i









Reviews: