DGSHAPE DWX-4 User Manual Download Page 40 | Manualshive

Page: 40 / 53

background image

40

Chapter 4 Read This Chapter Whenever You Face a Problem. (FAQ)

What to Do If…

Initialization Is Not Performed or Initialization Fails

Is a front cover open?

When starting the machine, make sure that the front cover is closed. For safety, initialization is not performed when a cover
remains open at startup.

Is anything caught on the spindle unit or rotary axis unit?

Check whether something has become caught and is impeding initialization.

Is the tool snagged?

The tool attached to the spindle unit or rotary axis unit may fail to perform initialization if it is snagged on the attachment.
Try to detach the tool using the emergency tool release function of VPanel.



P. 10, ""Maintenance" Tab"

The Operation Button Does Not Respond

Is a front cover or maintenance cover open?

Some operations of the machine will be limited if the front cover or the maintenance cover is open. Close all the covers.

Are you operating the operation button with a glove on?

The operation button does not respond if you wear a glove. Operate the operation button with a bare hand.

VPanel Does Not Recognize the Machine

Is the cable connected?

Make sure that the cables are connected.



"Setup Guide" ("Connecting Cables")

Is the driver installed correctly?

If the connection to the computer is not made in the sequence described, the driver may fail to be installed correctly. Unless
a driver is suitable, VPanel does not work. Check again to ensure that the connection was made using the correct procedure.



"Setup Guide" ("Installing and Setting Up the Software")



P. 46, "To Install Software and Electronic Manual Separately"



P. 47, "Installation Is Impossible"

Is the procedure correct when plural machines are connected or when the ID of any ma-

chine is changed?

There is a possibility that the connection method might be incorrect when more than one machine is connected. Check
the correct connection method. After the ID of a machine was changed, it is necessary to restart the machine and VPanel.



"Setup Guide" ("Connecting Multiple Units")



P. 5, "Displaying VPanel"

«
...
38
39
40
41
42
...
»

Summary of Contents for DWX-4






















































Reviews:

No comments

Related manuals for DWX-4

Brand: Tanco Pages: 72

Brand: HABYS Pages: 16

Brand: Acterna Pages: 72

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brand: Waters Pages: 4

Brand: Waterpik Pages: 2

Brand: MÄDLER Pages: 4

Brand: Martin Pages: 202

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands