DFI PT800-ALE User Manual Download Page 7

Page: 7 / 114

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• PT880-ALE

North bridge: VIA

PT880

Advanced high performance 128-bit DDR DRAM control-
ler

South bridge: VIA

VT8237

• PT800-ALE

North bridge: VIA

PT800

South bridge: VIA

VT8237

Processor

The system board is equipped with Socket 478 for installing one
of the following supported processors.

• Intel

Pentium

4 Processor with Hyper-Threading Technology

800MHz/533MHz system data bus

• Intel

Pentium

4 Northwood processor

533MHz/400MHz system data bus

• Intel

Celeron Northwood processor (478-pin)

400MHz system data bus

System Memory

• Suppor ts dual channel (128-bit wide) memor y interface

(PT880-ALE only)

• Two 184-pin DDR DIMM sockets
• Suppor ts up to 2GB using PC1600 (DDR200), PC2100

(DDR266), PC2700 (DDR333) and PC3200 (DDR400)
unbuffered DDR SDRAM DIMM, 2.6V type

Chapter 1 - Introduction

DIMMs

2MBx64
4MBx64
8MBx64

Memory Size

16MB
32MB
64MB

DIMMs

16MBx64
32MBx64
64MBx64

Memory Size

128MB
256MB
512MB

Summary of Contents for PT800-ALE



















































































































Search results

Summary of Contents for PT800-ALE

Reviews:

Related manuals for PT800-ALE

Brands by name

Popular brands

DFI PT800-ALE, User Manual

Search results

Summary of Contents for PT800-ALE

Reviews:

Related manuals for PT800-ALE

Brands by name

Popular brands