DFI PT800-AL User Manual Download Page 15

Page: 15 / 118

Introduction

1.2 Hyper-Threading Technology Functionality

Requirements

Enabling the functionality of Hyper-Threading Technology for your
computer system requires

ALL

of the following platforms.

Components:

• CPU - an Intel

Pentium

4 Processor with HT Technology

• Chipset - an Intel

chipset that supports HT Technology

• BIOS - a BIOS that supports HT Technology and has it enabled
• OS - an operating system that includes optimizations for HT

Technology

Please refer to Appendix A for information about enabling the
functionality of the Hyper-Threading Technology. For more information
on Hyper-Threading Technology, go to: www.intel.com/info/
hyperthreading.

1.3 Package Checklist

The system board package contains the following items:

The system board

A user’s manual

One Serial ATA data cable

One IDE cable for ATA/33/66/100/133 IDE drives

One 34-pin floppy disk drive cable

One SATA RAID floppy diskette

One I/O shield

One “Mainboard Utility” CD

If any of these items are missing or damaged, please contact your
dealer or sales representative for assistance.

Summary of Contents for PT800-AL























































































































Search results

Summary of Contents for PT800-AL

Reviews:

DFI PT800-AL, User Manual, Page: 15 / 118

Search results

Summary of Contents for PT800-AL

Reviews: