DFI P4X533-ALE User Manual Download

Page: 33 / 113

Hardware Installation

2.5.7 Audio (Audio Jacks and Front Audio)

Audio Jacks

The system board is equipped with 3 audio jacks at location
CN4. A jack is a one-hole connecting interface for inserting a
plug.

•

Line-out Jack (Lime)

This jack is used to connect external speakers for audio output
from the system board.

•

Line-in Jack (Light Blue)

This jack can be connected to the line-out jack of any exter-
nal audio devices such as Hi-fi set, CD player, AM/FM radio
tuner, synthesizer, etc. Connect a stereo cable from the line-
out jack of your external device to this line-in jack.

•

Mic-in Jack (Pink)

This jack is used to connect an external microphone.

Mic

Mic Power

AuD_R_Out

N. C.

AuD_L_Out

GND AuD_Vcc

Key

AuD_R_Return

AuD_L_Return

Front audio

Line-out

Line-in

Mic-in

p4x533-ale 80310409 2.pmd

2/18/2004, 8:13 AM

www.DataSheet4U.com

Summary of Contents for P4X533-ALE


















































































































Search results

Summary of Contents for P4X533-ALE

Reviews:

Related manuals for P4X533-ALE

Brands by name

Popular brands

DFI P4X533-ALE, User Manual

Search results

Summary of Contents for P4X533-ALE

Reviews:

Related manuals for P4X533-ALE

Brands by name

Popular brands