Dewetron DAQP-LA Series Technical Reference Manual Download Page 7

1 2 3 4 5

6 7 8 9

7

General Module Information

9-pin male SUB-D connector

Interface pin assignment:
1  Module output (±5 V) 

2  RS-485 (A) 

3  RS-485 (B) 

4 GND 

5  +9 V power supply 

6  +12 V power / sensor supply 

7  Module input (from D/A 

  converter of the A/D board)

1)

 

8 reserved 

9  -9 V power supply

1)

Triggerout at DAQP-FREQ-A

Calibration information

All DEWETRON modules are calibrated at 25 °C after a warmup time of 30 minutes and meet their 

specifications when leaving the factory.

 

The time interval for recalibration depends on environmental conditions. Typically, the calibration should be 

checked once a year.

Calibration certificates are available from DEWETRON as an option. DEWETRON offers two types:

 ISO traceable DEWETRON certificate

 Calibration certificate according to ÖKD (equivalent to DKD)

This manual contains no calibration information. For self calibration, there is a separate calibration kit for the 

DAQ series modules available. The CAL-KIT contains the required cables, software and instructions.

General module specifications

Module dimensions: 

20 x 65 x 105 mm 

(0.79 x 2.56 x 4.13 in.) 

(W x H x D without front cover and connectors)

Frontcover: 

20 x 87 x 2 mm 

(0.79 x 3.43 x 0.08 in.) 

(W x H x D without connector)

Environmental: 

Temp. range storage: 

-30 °C to +85 °C

(-22 °F to 185 °F) 

Temp. range operating:  -5 °C to +60 °C

(23 °F to 140 °F)

Relative humidity 

(MIL202): 

0 to 95 % at 60 °C, non-condensing (unless otherwise noticed)

RFI susceptibility: 

±0.5 % span error at 400 MHz, 5 W, 3 m

All specifications within this manual are valid at 25 °C!

All modules are produced according ISO9001 and ISO14001.

Module connectors

Frontpanel connector: 

Accessable to the user. The connector type and pin assignment varies 

from module to module. Detailed pin assignment of each module is 

shown in the appropriate module description.

Rear connector: 

9-pin male SUB-D, interface to the DEWE-System, not accessable to the user.

HSI/DAQx and PAD module 

rear view

450134 • DAQP/H

SI

/PAD Modules • Technical Reference Manual • Prin

t

ing version 2.3.4 • November 18, 2020

Summary of Contents for DAQP-LA Series















Reviews: