DeWalt XR Li-Ion DCD710-XE Instruction Manual Download Page 6

4

a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, 

hit with a hammer, stepped on). Damaged battery packs should be returned to service 

center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can 

contact exposed battery terminals. 

For example, do not place battery in aprons, 

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, 

keys, etc. 

Transporting batteries can possibly cause fires if the battery terminals 

inadvertently come in contact with conductive materials such as keys, coins, 

hand tools and the like. 

The US Department of Transportation Hazardous Material 

Regulations (HMR) actually prohibit transporting batteries in commerce or on 

airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly 

protected from short circuits. So when transporting individual batteries, make sure 

that the battery terminals are protected and well insulated from materials that could 

contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

 • 

Do not incinerate the battery pack even if it is severely damaged or is 

completely worn out. 

The battery pack can explode in a fire. Toxic fumes and 

materials are created when lithium ion battery packs are burned.

  •

 

If battery contents come into contact with the skin, immediately wash area 

with mild soap and water. 

If battery liquid gets into the eye, rinse water over the 

open eye for 15 minutes or until irritation ceases. If medical attention is needed, 

the battery electrolyte is composed of a mixture of liquid organic carbonates and 

lithium salts.

 • 

Contents of opened battery cells may cause respiratory irritation. 

Provide fresh 

air. If symptoms persists, seek medical attention.

WARNING:

 Burn hazard. Battery liquid may be flammable if exposed to spark or 

flame. 

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS:

 

This manual contains important safety and operating 

instruc tions for battery chargers.
  •  Before using charger, read all instructions and cautionary markings on charger, 

battery pack, and product using battery pack.

WARNING:

 

Shock hazard. Do not allow any liquid to get inside charger. Electric 

shock may result.

 ........ direct current 

 ...........alternating or direct current

 .............. Class I Construction 

no ..............no load speed

 ...................

(grounded) 

 .............earthing  terminal

 .............. Class  II  Construction 

..............safety alert symbol

 ...................

(double insulated)  

BPM ..........beats per minute

…/min ........ per minute 

RPM ..........revolutions per minute

IPM ............. impacts per minute

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and 

voltage. Consult the chart at the end of this manual for compatibility of chargers and 

battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack 

and charger, read the safety instructions below. Then follow charging procedures 

outlined.

READ ALL INSTRUCTIONS

  •

  Do not charge or use battery in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust. 

Inserting or removing the battery 

from the charger may ignite the dust or fumes.

 • 

Never force battery pack into charger. Do not modify battery pack in any 

way to fit into a non-compatible charger as battery pack may rupture 

causing serious personal injury. 

Consult the chart at the end of this manual for 

compatibility of batteries and chargers. 

  •  Charge the battery packs only in D

E

WALT chargers.

 • 

DO NOT 

splash or immerse in water or other liquids.

  •

  Do not store or use the tool and battery pack in locations where the 

temperature may reach or exceed 40 

˚

C (105 

˚

F) (such as outside sheds or 

metal buildings in summer).

WARNING:

 Fire hazard. Never attempt to open the battery pack for any reason. If 

battery pack case is cracked or damaged, do not insert into charger. Do not crush, 

drop or damage battery pack. Do not use a battery pack or charger that has received 

Summary of Contents for XR Li-Ion DCD710-XE

















Reviews: