background image

4

English

16. The narrow pin point stream is very powerful. It is not 

recommended for use on painted surfaces, wood surfaces or 

items attached with an adhesive backing. 

17.  Keep operating area clear of all persons and ani mals.

18.  Always use both hands when operating pressure washer to 

maintain complete control of the wand.

19.  Do not touch nozzle or water spray while operating. Never 

place hands in front of nozzle.

20.  Wear safety goggles while operating. Wear protective clothing 

and footwear to protect against accidental spraying.

21.  Disconnect power plug from the outlet when not in use and 

prior to the detaching of the high pressure hose.

22.  Never tie knots or kink the high pressure hose as da mage 

could result. Inspect the high-pressure hose regularly. Replace 

the hose immediately if it is damaged, worn or shows any signs 

of cracks, bubbles, pinholes, or other leakage. Never grasp a 

high-pressure hose that is leaking or damaged.

23.  Do not operate or store this product in temperatures below 

40 °F (4 °C). Freeze damage is not covered by the warranty.

24.  Carefully observe all chemical instructions and warnings before 

using. Use only approved pressure washer cleaners. Do not 

use bleach, chlorine, or any cleaners containing acids. Always 

follow manufacturer’s label recommendations for proper use 

of cleaners. Always protect eyes, skin and respiratory system 

from cleaners.

25.  The pressure washer should not be used in areas where gas 

vapors may be present. An electric spark could cause an 

explosion or fire. 

26.  To minimize the amount of water getting into the pressure 

washer, the unit should be placed as far as possible from the 

cleaning site during operation.

27. To prevent accidental discharge, the spray gun should be 

secured by locking the trigger when not in use. 

28.  To allow free air circulation, the pressure washer should NOT 

be covered during operation. 

29.  Never touch, grasp or attempt to cover a pinhole or similar 

water leak on the high-pressure hose. The stream of water IS 

under high pressure and WILL penetrate skin.

30.  Use only hoses and accessories rated for pressure higher 

than your pressure washer's psi. Never use with any other 

manufacturer’s accessories or components.

31.  Never defeat the safety fea tures of this product.

32.  Do not op er ate machine with missing, broken or un au tho rized 

parts.

33.  Never spray flammable liquids or use pressure washer in areas 

containing combustible dust, liquid, or vapors.

34.  DO NOT use an extension cord with this pressure washer.

WARNING: 

Risk of injection or injury. Do not direct discharge 

stream at persons.

SAVE THESE INSTRUCTIONS  

FOR FUTURE USE

MOTOR OVERLOAD

The electric motor in this pressure washer is equipped with an 

overload protection device which will automatically shut off the motor 

in the event the motor draws excessive current or overheats. Allow 

motor to cool and then reset thermal overload button on pump motor.

GROUNDING INSTRUCTIONS

This product must be grounded. If it should malfunction or breakdown, 

grounding provides a path of least resistance for electric current to 

reduce the risk of electric shock. This product is equipped with a cord 

having an equipment-grounding conductor and a grounding plug. The

Summary of Contents for DXPW2000E

















Reviews: