background image

3

English

Hot Surfaces

MODEL

DXCMTB5590856

APPROX. BLOW OFF PRESSURE

150 psi

SCFM @ 100 PSI 

9.9 *

* Tested per ISO 1217

Definitions: Safety Guidelines 

The definitions below describe the level of severity 

 

for each signal word. Please read the manual and pay 

attention to these symbols.

DANGER:

 Indicates an imminently hazardous situation 

which, if not avoided, 

will 

result in 

death or serious injury

.

WARNING:

 Indicates a potentially hazardous 

 

situation which, if not avoided, 

could

 result in 

death or 

serious injury

.

CAUTION

: Indicates a potentially hazardous 

 

situation which, if not avoided, 

may

 result in 

minor or 

moderate injury

.

NOTICE: 

Indicates a practice 

not related to personal injury

 

which, if not avoided, 

may

 result in 

property damage. 

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT 

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT: 

 

1-888-895-4549 

Important Safety Instructions

DANGER: Carbon Monoxide. Using an engine indoors can 

kill  you  in  minutes.  Engine  exhaust  contains  high  levels  of 

carbon monoxide (CO), a poisonous gas you cannot see or 

smell.  You  may  be  breathing  CO  even  if  you 

DO NOT

  smell 

 

engine exhaust.

OUTLET TUBE

ENGINE 

MUFFLER

GASOLINE 

ENGINE

COMPRESSOR 

CYLINDER & HEAD

PUMP 

CRANKCASE

FIG. 2

Summary of Contents for DXCMTB5590856






























Reviews: