background image

• Keep hands and body parts clear of

immediate work area.

 Hold workpiece

with clamps when necessary to keep
hands and body out of potential harm. Be
sure the workpiece is properly secured
before pressing the stapler against the
material. The contact trip may cause
the work material to shift unexpectedly.
(Fig. Q)

• Do not use tool in the presence of

flammable dust, gases or fumes.

 The

tool may produce a spark that could ignite
gases causing a fire. Driving a fastener into
another fastener may also cause a spark.
(Fig. R)

• Keep face and body parts away from

back of the tool cap when working
in restricted areas. 

Sudden recoil can

result in impact to the body, especially
when stapling into hard or dense material.

(Fig. S)

• Grip tool firmly to maintain control

while allowing tool to recoil away
from work surface as fastener is
driven.

 In “Contact Actuation Mode” if

contact trip is allowed to recontact work
surface before trigger is released an
unwanted fastener will be fired.

• Choice of triggering method is

important.

 Check the manual for triggering options.

CONTACT ACTION TRIGGER

• When using the contact action

trigger, be careful of unin tentional
double fires resulting from tool
recoil. 

Unwanted fasteners may be

driven if the contact trip is allowed to
accidentally re-contact the work surface.

(Fig. T)

TO AVOID DOUBLE FIRES:

 

•  

Do not engage the tool against the

work surface with a strong force.

 

•  

Allow the tool to recoil fully after each actuation.

 • Use sequential action trigger.

• When “contact” actuating the stapler, always keep

tool in control.

 Inaccurate placement of tool can result in

misdirected discharge of a fastener.

SEQUENTIAL ACTION TRIGGER

• When using the sequential action trigger, do not actuate

the tool unless the tool is placed firmly against the
workpiece.

•  

DEPTH ADJUSTMENT: To reduce risk of serious injury

from accidental actuation when attempting to adjust depth,

ALWAYS;

• Disconnect air supply
•  

Avoid contact with trigger during adjustments

FIG. Q

FIG. R

FIG. S

FIG. T

English

4

Summary of Contents for DWSL18CAP















Reviews: