9
10
SCAN CHECK (FIG. 7)
1. Place the tool in an area between two vertical surfaces that are at
least 9 m apart. Mount the tool exactly midway to the wall.
2. Position the tool at an angle of 45° to the left.
3. Switch on the horizontal laser beam.
4. Mark the centre of the laser beam exactly midway on the opposite
wall.
5. Switch off the tool and rotate it 90° clockwise.
6. Switch on the horizontal laser beam.
7. Mark the centre of the laser beam exactly midway on the opposite
wall.
8. Switch off the tool.
9. Measure the difference between the markings.
10. If the difference between the markings is 3 mm or less, the tool is
properly calibrated.
11. If the difference between the markings is more than 3 mm, the tool
must be serviced.
LEVEL CHECK (FIG. 8A, 8B)
1. Place the tool in an area with a wall of at least 9 m length. Mount
the tool to one end of the wall.
2. Position the tool at an angle of 90° to the left.
3. Switch on the horizontal laser beam.
4. Mark the centre of the laser beam at one-third distance (FF) and at
two-third distance (GG) on the wall.
5. Switch off the tool.
6. Mount the tool to the other end of the wall.
7. Position the tool at an angle of 90° to the right.
8. Switch on the horizontal laser beam.
9. Switch on the tool, align the laser beam with the wall marking (GG)
and mark the laser beam at two-third distance (HH) on the wall.
10. Switch off the tool.
11. Measure the difference between the markings (FF, HH).
12. If the difference between the markings is 6 mm or less, the tool is
properly calibrated.
13. If the difference between the markings is more than 6 mm, the tool
must be serviced.
FIG. 8A
FIG. 8B
FF
GG
HH
GG
PLUMB CHECK (FIG. 9A, 9B)
1. Place the tool on the floor in an area with a ceiling of at least 2,5 m
height.
2. Mark a line of 1,5 m length (II) on the floor. Position the tool at one
end of the floor marking (II).
3. Switch on the vertical laser beam.
4. Align the laser beam with the floor marking (II).
5. Mark the centre of the laser beam at one-third distance (JJ) and at
two-thirds distance (KK) on the ceiling.
6. Switch off the tool. Position the tool at the other end of the floor
marking (II) facing the marking.
7. Switch on the vertical laser beam.
FIG. 9A
FIG. 9B
JJ
KK
LL
II
II
8. Align the laser beam with the floor marking (II).
9. Mark the centre of the laser beam at one-third distance (LL) and at
two-thirds distance (MM) on the ceiling.
10. Switch off the tool.
11. Measure the difference between the markings (JJ, LL).
12. Measure the difference between the markings (KK, MM).
13. If the difference between the markings is 3,5 mm or less, the tool is
properly calibrated.
14. If the difference between the markings is more than 3,5 mm, the
tool must be serviced.
Cleaning
Exterior plastic parts may be cleaned with a damp cloth. Although these
parts are solvent resistant, NEVER use solvents. Use a soft, dry cloth to
remove moisture from the tool before storage.
Repairs
NOTE: Disassembling the laser will void all warranties on the product.
To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by certified service centers or other
qualified service organizations.
Accessories
WARNING: Since accessories, other than those offered by
D
e
WALT
,
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only
D
e
WALT
recommended accessories should be used with this product.
USING THE LASER WITH ACCESSORIES (FIG. 1 INSET)
The laser is equipped with a 1/4" x 20 female thread (K) on the bottom
of the unit. This thread is to accommodate current or future D
e
WALT
accessories. Only use D
e
WALT accessories specified for use with this
product. Follow the directions included with the accessory.
These are:
• DE0881-XE D
e
WALT tripod
• DE0892-XE D
e
WALT detector
Consult your dealer for further information on the appropriate
accessories.
Recommended accessories for use with your tool are available at
extra cost from your local service center. If you need any assistance
in locating any accessory, please contact Stanley Black & Decker, 82
Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ)
0800 339 258.
Batteries
When disposing batteries, think of the protection of the environment.
Check with your local authorities for an environmentally safe way of
battery disposal.
