manualshive.com logo in svg

DeWalt DPD3800, Instruction Manual

Share
Download
DeWalt DPD3800 Instruction Manual Download Page 15

15

English

Pump

note:

 The pump was filled with oil at the factory. 

  1. Change pump oil after the first 10 hours of operation and every 

250 hours thereafter.

to check oIL

  1. The oil level should come to the 

Q

AA

Z

dot  in  the  middle  of  the  sight 

glass (Z).

hoW to chanGe PuMP oIL

  1. Loosen pump oil plug (Q).
  2. Place  a  container  under  the  oil 

drain plug (AA).

  3. Remove pump oil drain plug.
  4. After  oil  is  drained,  replace  oil 

drain plug. Tighten securely.

  5. 

Remove pump oil plug and fill with 14 oz. (414 ml) of DP70 pump 

oil. If DP70 is not available use 30W non-detergent oil.

  6.  Replace pump dipstick/oil plug and tighten securely.

nozzle cleaning

If the nozzle becomes clogged with foreign materials, such as dirt, 

excessive  pressure  may  develop.  If  the  nozzle  becomes  partially 

clogged  or  restricted,  the  pump  pressure  will  pulsate.  Clean  the 

nozzle immediately using the nozzle kit supplied and the following 

instructions:
  1. Shut off the pressure washer and turn off the water supply.
  2. Pull trigger on gun handle to relieve any water pressure.
  3. Disconnect the spray wand from the gun.

  4. Remove the high-pressure nozzle from the 

Y

spray  wand.  Remove  any  obstructions 

with the nozzle cleaning tool (Y) provided 

and back flush with clean water.

  5. Direct water supply into spray wand to 

back  flush  loosened  particles  for  30 

seconds.

  6. Reassemble the nozzle to the wand. 
  7. Reconnect spray wand to gun then turn on water supply.
  8. Start pressure washer and place spray wand into high pressure 

setting to test.

To clean the Water Inlet Filter

This filter screen (U) should be checked periodically and cleaned if 

necessary.
  1. Remove the filter screen (U) by grasping the

U

 

end  and  removing  it  from  water  inlet  of 

pump.

  2. Clean filter by flushing it with water on both 

sides.

  3. Reinsert filter into water inlet of pump. Cone 

side faces out.

note:

 Do not operate pressure washer without 

filter properly installed.

To remove Tires

  1. Using  a  1/8"  (3.2    mm)  hex  head  wrench

 

loosen set screw in hub collar.

  2. Slide  hub  collar  from  axle  and  remove  the 

tire. 

Summary of Contents for DPD3800






















Reviews:

No comments

Brands by name

Popular brands

Load more brands