3
•
Young children and the infirm.
This appliance is not intended for use by
young children or infirm persons without supervision. Young children should be
supervised to ensure that they do not play with this appliance.
•
Replacement of the supply cord.
If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised D
E
WALT Service Centre in order
to avoid a hazard.
Extension Cords
CAUTION:
Use only extension cords that are approved by the country’s Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
MINIMUM GAUGE FOR CORD SETS
For Cable length (m):
7.5 15 25 30 45 60
Use Cable with minimum rating (Amperes)
Tool Amperes
0 - 3.4
7.5
7.5
7.5
7.5
7.5
7.5
3.5
-
5.0 7.5 7.5 7.5 7.5 10 15
5.1 - 7.0
10
10
10
10
15
15
7.1 - 12.0
15
15
15
15
20
20
12.1 - 20.0
20
20
20
20
25
–
Safety Warnings for Impact Drivers and Wrenches
•
Hold power tool by insulated gripping surfaces when performing an operation
where the fastener may contact hidden wiring.
Fasteners contacting a “live”
wire may make exposed metal parts of the power tool “live” and could give the
operator an electric shock.
• Use clamps or other practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
•
Wear safety goggles or other eye protection.
Hammering and drilling operations
cause chips to fly. Flying particles can cause permanent eye damage.
•
Bits, sockets and tools get hot during operation.
Wear gloves when touching
them.
•
Air vents often cover moving parts and should be avoided.
Loose clothes,
jewellery or long hair can be caught in moving parts.
•
Do not operate this tool for long periods of time.
Vibration caused by tool action
may be harmful to your hands and arms. Use gloves to provide extra cushion
and limit exposure by taking frequent rest periods.
WARNING: ALWAYS wear approved protective safety equipment complying with
the following standards:
• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;
• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;
• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
•
Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water.
Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
WARNING:
Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from
face and body.
WARNING:
We recommend the use of a residual current device with a residual
current rating of 30mA or less.
WARNING: Always wear proper personal hearing protection that conforms to
AS/NZS1270 during use.
Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
