DeWalt DC390B Manual Download Page 20

Page: 20 / 20

English

WALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any
way. D

WALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by
law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your
D

WALT Power Tool, Laser, or Nailer for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund
– no questions asked.

LATIN AMERICA:

This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country
specific warranty information contained in the packaging, call the local
company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT:

If your warning labels

become illegible or are missing, call 1-800-4-D

WALT (1-800-433-

9258) for a free replacement.

Summary of Contents for DC390B





















Search results

Summary of Contents for DC390B

Reviews:

Related manuals for DC390B

Brands by name

Popular brands

DeWalt DC390B, Manual

Search results

Summary of Contents for DC390B

Reviews:

Related manuals for DC390B

Brands by name

Popular brands