DeWalt DC305-XE Instruction Manual Download Page 7

5

 • 

Contents of opened battery cells may cause respiratory irritation.

 

Provide fresh 

air. If symptoms persists, seek medical attention.

WARNING: 

Burn hazard. Battery liquid may be flammable if exposed to spark or 

flame. 
  •  Charge the battery packs only in D

E

WALT chargers.

 • 

DO NOT 

splash or immerse in water or other liquids.

  •  Do not store or use the tool and battery pack in locations where the 

temperature may reach or exceed 40

˚

C (105°F) (such as outside sheds 

or metal buildings in summer).

WARNING:

 Never attempt to open the battery pack for any reason. If battery 

pack case is cracked or damaged, do not insert into charger. Do not crush, drop or 

damage battery pack. Do not use a battery pack or charger that has received a sharp 

blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with 

a hammer, stepped on). Damaged battery packs should be returned to service center 

for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can 

contact exposed battery terminals. 

For example, do not place battery in aprons, 

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, 

etc. 

Transporting batteries can possibly cause fires if the battery terminals 

inadvertently come in contact with conductive materials such as keys, coins, 

hand tools and the like.

 The US Department of Transportation Hazardous Material 

Regulations (HMR) actually prohibit transporting batteries in commerce or on air-

planes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly 

protected from short circuits. So when transporting individual batteries, make sure 

that the battery terminals are protected and well insulated from materials that could 

contact them and cause a short circuit.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on

 

the lithium ion battery (or battery pack) indicates that the costs to 

recycle the battery (or battery pack) at the end of its useful life 

have already been paid by D

E

WALT.

RBRC™ in cooperation with D

E

WALT and other battery users, has 

established programs in the United States to facilitate the collection of spent lithium 

ion batteries. Help protect our environment and conserve natural resources by return-

ing the spent lithium ion battery to an authorized D

E

WALT service center or to your 

local retailer for recycling. You may also contact your local recycling center for infor-

mation on where to drop off the spent battery.
RBRC™ is a registered trademark of the 

Rechargeable Battery Recycling Corporation.

Storage Recommendations

  1.  The best storage place is one that is cool and dry away from direct sunlight and 

excess heat or cold.

  2.  Long storage will not harm the battery pack or charger. Under proper conditions, 

they can be stored for 5 years or more.

Charger

Your battery pack requires a 1 hour D

E

WALT charger. Be sure to read all safety 

instructions before using your charger. Consult the chart on the back of this 

manual for compatibility of chargers and battery packs.

Charging Procedure 

 

  1.  Plug the charger into an appropriate outlet before inserting the battery pack.
  2.  Insert the battery pack into the charger. The charger is equipped with a three-light 

fuel gauge that will blink according to the state of charge of the battery pack.

  3.  The completion of charge is indicated by the three red lights remaining ON 

continuously. The pack is fully charged and may be used at this time or left 

on the charger.

Charger Diagnostics

This charger is designed to detect certain problems that can arise with the battery 

packs or the charger. Problems are indicated by the three red lights flashing together 

in different patterns.

PROBLEM POWERLINE

When the charger is used with some portable power sources such as generators or 

sources that convert DC to AC, the charger may temporarily suspend operation. The 

Summary of Contents for DC305-XE

















Reviews: