DeWalt D28114N-XE Instruction Manual Download Page 12

Page: 12 / 20

NOTE:

The guard is pre-adjusted to the diameter of the

FIG. 5

gear case hub at the factory. If, after a period of time, the

guard becomes loose, tighten the adjusting screw (M)

with clamp lever in the closed position.

CAUTION:

Do not tighten the adjusting screw with

the clamp lever in open position. Undetectable

damage to the guard or the mounting hub may result.

CAUTION:

If guard cannot be tightened by adjusting clamp, do not use tool and

take the tool and guard to a service center to repair or replace the guard.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn off and unplug the

tool before making any adjustments or removing or installing attachments or

accessories.

Before reconnecting the tool, depress and release the paddle switch to

ensure that the tool is off. An accidental start-up can cause injury.

Proper Hand Position

WARNING:

To reduce the risk of serious personal injury,

ALWAYS

use proper hand

position.

WARNING:

To reduce the risk of serious personal injury,

ALWAYS

hold securely in

anticipation of a sudden reaction.
Proper hand position requires one hand on side handle with the other hand on the

main handle.

Guards and Flanges

It is important to choose the correct guards and flanges to use with the grinder

accessories. See pages 9–10 for the correct accessories.

NOTE

: Edge grinding and cutting can be performed with Type 27 wheels designed and

specified for this purpose.

WARNING:

Accessories must be rated for at least the speed recom mended on the

tool warning label. Wheels and other accessories running over rated accessory speed

may burst and cause injury. Every unthreaded accessory must have a 2.23 mm

(7/8”) arbor hole. If it does not, it may have been designed for a circular saw and

should not be used. Use only the accessories shown on pages 9–10. Accessory

ratings must be above listed minimum wheel speed as shown on tool nameplate.

115 mm and 125 mm (4-1/2" and 5") Sanding Flap Discs

Quick-change

backing flange

Non-hubbed sanding flap

disc

Threaded clamp nut

Type 27 guard

Hubbed sanding flap

disc

Type 27 guard

Summary of Contents for D28114N-XE





















Search results

Summary of Contents for D28114N-XE

Reviews:

Related manuals for D28114N-XE

Brands by name

Popular brands

DeWalt D28114N-XE, Instruction Manual

Search results

Summary of Contents for D28114N-XE

Reviews:

Related manuals for D28114N-XE

Brands by name

Popular brands