DeWalt D25113-XE Instruction Manual Download Page 9

7

DRILLING IN MASONRY

(D25113-XE, D25114-XE, D25213-XE, D25313-XE, D25314-XE)

When drilling in masonry, use SDS carbide tipped bits rated for percussion drilling and 

be certain that the bit is sharp. Use a constant and firm force on the tool to drill most 

effectively. A smooth, even flow of dust indicates the proper drilling rate.

DEPTH ROD

To adjust the depth rod.
  1.  Push in and hold the button on the side handle. 
  2.  Move the depth rod (B) so the distance between the end of the rod and the end 

of the bit equals the desired drilling depth. 

  3.  Release the button to lock rod into position.  When drilling with the depth rod, 

stop when end of rod reaches surface of material.

MAINTENANCE

WARNING:

 

Shock Hazard.

 To reduce the risk of serious personal injury, turn tool 

off and disconnect tool from power source before making any adjustments or 

removing/installing attachments or accessories.

Cleaning 

CAUTION: 

Never use solvents or other harsh chemicals for cleaning the non-

metallic parts of the tool. These chemicals may weaken the plastic materials used in 

these parts. Use a cloth dampened only with water and mild soap. Never let any liquid 

get inside the tool; never immerse any part of the tool into a liquid.

Lubrication

Your tool was properly lubricated before leaving the factory. In from two to six 

months, depending upon use, take or send your tool to an authorized service 

center for a complete cleaning, inspection and lubrication. Tools used constantly 

on production jobs will need relubrication more often. Also, tools “out of service” for 

long periods should be relubricated before being put back to work.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment 

(including brush inspection and replacement) should be performed by certified 

service centers or other qualified service organizations, always using identical 

replacement parts.

ACCESSORIES

WARNING:

 

Since accessories, other than those offered by D

E

WALT, have not been 

tested with this product, use of such accessories with this tool could be hazardous. 

To reduce the risk of injury, only D

E

WALT, recommended accessories should be used 

with this product. 
Recommended accessories for use with your tool are available at extra cost from your 

local service center. If you need any assistance in locating any accessory, please con-

tact D

E

WALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 Australia or 

call 1800 654 155 or (NZ) 09 579 7600.

MAXIMUM RECOMMENDED CAPACITIES

 D25113-XE, 

D25114-XE

    D25213-XE, D25314-XE, D25315-XE

  Masonry  

26 mm (1") 

 Steel 

12.7 mm (1/2") 

  Wood 

38 mm (1-1/2") 

 OPTIMUM CAPACITY

  Masonry 

4 mm - 16 mm

  

(5/32"-5/8")

Guarantee

Applicable to hand held Power Tools, Lasers and Nailers.

Three Year Limited Warranty

D

E

WALT will repair, without charge, any defects due to faulty materials or 

workmanship for three years from the date of purchase. Please return the complete 

unit, transportation prepaid, to any D

E

WALT Service Centre, or any authorised 

service station.  
For warranty repair information, call 

(AUS) 1800 654 155

 or 

(NZ) 09 579 7600

.

This warranty does not apply to 

• Accessories 
•  Damage caused where repairs have been made or attempted by others. 
•  Damage due to misuse, neglect, wear and tear, alteration or modification.

Summary of Contents for D25113-XE













Reviews: