background image

14- ENG

D28713

STARTING

Prior to starting, refer to your engine manual for proper starting procedures
for your engine type.

1.

In a well ventilated outdoor area 

add fresh high quality unleaded gasoline

with a pump octane rating of 86 or higher.  Do not overfill. Wipe up spilled
fuel before starting the engine. Refer to engine manual for correct procedure.

2.

Check engine oil level.

See Engine Owners Manual for correct procedure.

NOTE: There will be a slight amount of oil in the engine from factory
testing.

3.

Verify the filter screen

is in water inlet of pump.

NOTE: 

Cone side faces out.

4.

Connect

water source to pump inlet.

NOTE:

Water source must provide a minimum of 5

gallons per minute at 20 p.s.i. 

5.

Connect

high pressure hose to pump outlet.

6.

If applying a chemical or cleaning solution

, see

How To Apply Chemicals/Cleaning Solvents in
Operation section of this manual.

7.

Turn water source on.

8.

Start engine.

See Engine Owners Manual for

correct procedure. 

NOTE: 

If the engine does not

start after two pulls, pull the trigger to relieve the
pressure. 

9.

Depress trigger on gun to start water flow.
NOTE: Stand on a stable surface

and grip

gun/wand firmly with both hands. Expect the gun
to kickback when triggered.

10. Release trigger to stop water flow.

11. Adjust nozzle spray for the task

being performed or change quick connect

tip. See How To Use Wand instructions in this section.

SHUTTING DOWN

1.

After each use,

if you have applied chemicals, place chemical hose into

container of clean water and draw clean water through chemical injection system
to rinse system thoroughly.

NOTE:

Failure to do so could cause damage to the

pump.

2.

Turn engine off.

See Engine Owner’s Manual. 

NOTE:

NEVER turn the water

off with the engine running.

3.

Turn water source off.

4.

Pull trigger on spray gun

to relieve any water pressure in hose or spray gun.

5.

See Storage section

in this manual for proper storage procedures.

Filter Screen

Water

Source

High

Pressure

Hose

Hook-up

Summary of Contents for EXCELL VR2400























Reviews: