OSD Menu Operation
A.
OSD menu flow chart
The function indicated with * for default setting.
B.
Tact Switch Operation
This camera utilizes a user menu “
Set Up Menu
“ that is displayed on the
monitor. To set items on the “
Set Up Menu
“, use the following buttons on
the side panel.
UP Key:
This button is used to move the cursor upwards.
Down Key:
This button is used to move the cursor downwards.
Right Key:
This button is used to move the cursor to the right.
Use this button to select or adjust the parameters of the selected item.
The parameter changes each time this button is pressed.
Left Key:
This button is used to move the cursor to the left.
Use this button to select or adjust the parameters of the selected item.
The parameter changes each time this button is pressed.
Set Key:
This button is used to set the determined parameter. If the item
has its own setting menu ( indicted by ), press this button to display the
next page setting menu.
C.
Opening the Set Up Menu
Press SET Key for three second. The
“ SET UP MENU “ will appear on the
monitor as shown on right side. Check
the current settings on the menu.
Refer to the sections below for a
detailed description of menu items. If
you decide not to make any changes
after checking the current settings,
move the cursor to “ QUIT“ and press
SET Key to close the “ SET UP MENU
“ and return to normal camera picture.
D.
Reset
Reset
allows you to reset all setup menu items to the factory settings if you are
unsure about the correct settings. Proceed as follows: Move OSD cursor to
“
Reset
“ and press
SET Key
. The words “
Resetting
“ momentarily appear on
the monitor. At this time all adjustments and parameters are reset to the
factory default settings.
Note:
If no button is pressed for 30 second while the OSD menu or any other setting
menu is displayed, the menu is automatically canceled and returns to the normal
camera picture.
4
FUNCTION OPERATION
1.
Synchronization Setting (SYNC)
You can select internal sync mode (
INT
) or line-lock mode (
LL
).
a. Use
UP Key
and
Down Key
move the cursor to the
Sync
parameter and use
Right Key
or
Left Key
to select line-lock (
LL
) or internal (
INT
), and press
SET Key
.
b.If
LL
is selected, the
Sync
second menu appears, If
INT
is selected, the
synchronization mode is automatically set to internal sync , and the menu is
displayed
INT
.
1-1.
Line-lock Sync Mode (LL)
The line-lock mode has its own menu for line-lock vertical phase adjustment.
When the vertical phase adjustment menu appears on the monitor. use
Right
Key
or
Lift Key
to move the cursor for phase adjustments. If the camera
installation is relocated, check the vertical phase adjustment again since the AC
line phase may be different.
Note:
The line-lock (
LL
) sync mode is not available when the camera operates
on DC power.
How to make sure the Phase:
Set the oscilloscope to the vertical rate and expand the vertical sync portion on
the oscilloscope.
Press
Right Key
or
Lift Key
of the camera to match the vertical phase for both
video output signals as closely as possible.
Phase adjustment range can be incremented in 16 steps by 22.5 degrees.
When
Right Key
or
Lift Key
is kept pressed for a second or longer, the "
I
"
cursor moves faster.
Note : If the AC line contains noise (spike noise, etc.), the stability of
the vertical phase of the camera video output signal may be disturbed.
2.
Shutter Speed Setting (Shutter)
To select electronic shutter speed, you can select an manual electronic shutter
speed of 1/50 (1/60), 1/120 (1/100). 1/250. 1/500, 1/1000, 1/2000, 1/4000,
1/10000 seconds. Or
A
uto
E
lectronics
S
hutter ( AES ). The 1/50 (1/60) is shutter
OFF. This function is effective to raise the sensitivity in low light conditions when
OFF is selected for Auto IRIS Lens. Move the cursor to the
Shutter
parameter
and select the electronic shutter speed. The preset values for Shutter (electronic
shutter speed) change by pressing
Right Key
or
Lift Key
as follows:
3.
Lens
3-1 Bright
This item is used to adjust the level of auto iris tens drive which supplied to DC
drive lens or video iris lens. Before operation make sure that connection is
correct for video auto iris lens or DC auto iris lens.
a.
Move the cursor to the
Lens
parameter and press
SET Key
, the second
menu of
Lens
is appear on the monitor.
b.
Change the curser by
Right Key
or
left Key
to adjust IRIS to close or open.
Once the picture is optimum move curse to
Back
and press
SET key
to safe
setting and return to top menu.
3.2 BF
This function is allow installer very easy to adjust optical back focus. When used
auto iris lens, this function will automatically fully open the IRIS of lens and change
to AES ( auto electronics shutter ). In case of manual lens, this function will
automatically switch to AES.
a.
Move curse to
Lens
by
Control Key
, change to
BF
and press
SET key
. In
the meantime “
Press SET for return
” is display on monitor.
b.
Adjust optical back focus to optimum position that press SET key for return to
top menu. ( Please refer to section
H
Focus and Back Focal Adjustment )
4.
BLC
This provide camera incase face strong light to have compensation luminance on
monitor. There are six BLC pattern and each are could adjust compensation level.
Compensation area indicated as below
5.
Configure
5-1. Aperture
, Move the curse to
Aperture
and press
SET key
. The second menu
will appear. Move the “
I
“ to adjust V-Aperture and H-Aperture level.
5-2. Gamma
, Move the curse to
Gamma
and press
SET key
. The second menu will
appear. Use
Lift
and
Right key
to select gamma 0.45, 0.8 or 1.
5-3. Pedestal
, Move the curse to
Pedestal
and press
SET key
. The second menu
will appear. Move the “
I
“ to adjust pedestal level.
5-4. Chroma
, Move the curse to
Chroma
and press
SET key
. The second menu
will appear. Move the “
I
“ to adjust Chroma level.
5-8. AGC,
7 limited value could select to limit enhance gain of AGC circuit, also select
OFF
could closed AGC function and select
Sens Up
to have maximum value (38dB) of
AGC gain.
6.
White Balance
6-1. WB-Auto
( White Balance Auto), In this mode, the color temperature is
monitored continuously and thereby white balance is set automatically. The color
temperature range for the proper white balance is approximately 2500 - 9100K.
6-2. WB-Menu
(
White Balance Menu), This mode provide user to adjust
white balance by manual adjust, There are R-gain and B-gain could adjust
independent.
6-3. WB-Push
, Move curse to WB-Push. Press on
SET key
to start the white
balance tracing. When the white balance setting is completed, release
SET key
and
push white was completely.
7.
CAM Title
The camera provide text generation on the display monitor. The 16 character in one
line is available for CAM Title function.
5
8.
D/N
This function provide camera automatically switch from color camera to B/W
camera by auto detect luminance, manual switch or external contact terminal by
IR lamp on rear panel.
8-1. Fuzzy
, The camera switch to B/W camera by auto detect luminance.
D/N Level
, the detect level could be select by
Low
or
High
.
Burst On
, Keep Burst signal when camera changes to B/W mode.
Burst Off
, Remove Burst signal when camera changes to B/W mode.
8-2. IR Pass
, Change camera to B/W camera by selects this function.
Burst On
, Keep Burst signal when camera changes to B/W mode.
Burst Off,
Remove Burst signal when camera changes to B/W mode.
8-3. IR Cut,
Close Day/Night function, keep camera on color mode, at this
mode the camera will not accept IR luminance.
9.
RS485
Before operation is function make sure correct connection on rear panel for
RS485.
Provide 000 ~ 999 ID address, 3 Password to protect RS485 setting.
Use arrow key to move curse to RS485 and press
SET key
,
Password
, Before into RS485 setting. Camera system request 3 character
password, input correct password to second menu.
Note
, before password change the default password is 000.
Address
, provide 000 ~ 999 ID address. Wrong address ID setting both
control and receive will cause remote control no function.
B-rate
, Baud rate setting, provide 2 rate select 4800 or 9600.
Note
, Incorrect baud rate setting will cause remote control no function.
Package
Camera
1pcs.
Instruction Manual
1pcs.
CCD Protect Cover
1pcs.
Main Power Cable ( Main power model only )
1pcs
Specification
General
PAL Model / NTSC Model
Image Size
1/3 Format Interline CCD Sensor
Pixel Element
PAL Model : 768 (H)
×
582 (V) approx. 440K pixels
NTSC Model : 768(H) x 494 (V) approx. 380K pixels
Scanning Frequency
PAL 2 : 1 Interlace / H : 15625Hz , V : 50Hz
NTSC 2: 1Interlance / H : 15750Hz, V : 60Hz
Operation Temperature
-10
℃
~ +50
℃
Storage Temperature
-20
℃
~ +60
℃
Output Terminal
BNC 75Ohm Unbalance
Power Source
Dual Switching Mode Power Supply DC12V / AC24V
±
20%
Universal Switching Power Supply AC100V ~ AC240V
Power Consumption
4.5 W Max,
Power Indicator
3
θ
Green LED on Rear Panel
IRIS Connector
4 pin Connector For DC Drive Lens ( Panasonic Standard )
3pin Terminal Block For Video Drive Lens
Lens Mount
CS Mount, Change C Mount by Adaptor.
Mounting Hole
1/4” Top and Bottom
External Dimension
73mm (W) x 63mm (H) x 122mm (D)
Weight TBD
Functional Specification
Auto IRIS Control
Video Drive / DC Drive Separate Output
* Day & Night
Optical Low Pass Filter Removable
* IR Lamp Trigger
External Relay Contact for GND Loop
Chroma Separate
CS / Color Killer
* Color Killer
ON / OFF / Fuzzy
SYNC System
INT / Line Lock
Line Lock
Phase Adjust Range 0
°
~ 270
°
Frequency Range PAL 50Hz
±
1Hz / NTSC : 60Hz
±
1Hz
Remote Controller
RS-485 two way communications
Camera Addressable
001 ~ 999
Text Display
16 Character with one line
Resolution
470 TV Line
Minimum Illumination
0.5Lux @F=1.2 ( 50IRE Video Output )
Video Output
1.0Vpp 75Ohm BNC unbalance
S/N Ratio
50dB
Gamma Compensation
3 Curve Selectable ; 0.45 / 0.8 / 1
Function Control or Selectable By OSD and RS-485
SYNC System
INT / LL Selectable
V-Phase 0
°
~ 270
°
Exposure Control
Auto Electronics Shutter / Manual Electronics Shutter
/ Auto IRIS lens
Auto Electronics Shutter
Max, Limit and Level Adjustable
Menu Electronics Shutter
8 Step 1/50 (1/60), 1/120 (1/100) , 1/250 , 1/500
1/1000 , 1/2000 , 1/4000 , 1/10000
Auto IRIS Lens Driver
Video IRIS lens / DC IRIS lens
Lens Level Control
Both For DC IRIS Lens and Video IRIS Lens
BLC
6 Area Select and Level Adjustable; Center 1, Center 2,
Door Way 1, Door Way 2, Upper Half, Lower Half.
White Balance Control
Auto White Balance / Push White Balance /
Menu White Balance
Auto White Balance
2 Application Range Selectable;
2500K ~ 9500K / 2000K ~ 18000K
Menu White Balance
1 Preset; R gain / B gain Adjustable
Gain Control
Auto Gain Control
Auto Gain Control
12dB ~ Sensitivity up (38dB max.) Adjustable.
Gamma Control
3 Step Selectable; 0.45 / 0.8 / 1
Aperture Control
0 ~ 15 IRE Max. For Vertical and Horizontal
Chroma Level
Adjustable
* Color Killer
ON / OFF / Fuzzy Selectable
* Day/Night
IR Pass / IR Cut / Fuzzy
Remote Control
RS-485, Two way communications
Address
001 ~ 999 ID selectable
Note : Function indicated * for System Day/Night model only.
Document Nr. : TOM-20030606-01B
Version Nr. : 030804A
Part Nr. : 531-CD000-000
6
Set key
Right key
Down key
Up key
Left key
Detect
Area
CENTER 1
CENTER 2
Detect
Area
DOORWAY 1
Detect
Area
DOORWAY 2
Detect
Area
LOW HALF
Detect
Area
UP HALF
Detect
Area
TOP MENU
SECOUND MENU
THIRD MENU
BF
Lens
Bright
Configure
Chroma
Level
Pedestal
Level
Aperture
H-APT Level
V-APT Level
Sync
INT *
LL
V-Phase
BLC
Off *
Center 1
Center 2
Door Way 1
Up Half
Low Half
Level
Door Way 2
Gamma
0.45 *
0.8
1
RS485
Address _ _ _
B-Rate
9600dps *
Address
4800dps
Password Setting
Password _ _ _
Shutter
AES
1/2K
1/60(1/50) *
1/100(1/120)
1/250
1/500
1/1K
1/2K
1/4K
1/10K
Bright
1/5K
1/10K
1/20K
1/50K *
1/100K
Text
CAM Tilte
Position
Off
*
On
D/N
IR Pass
IR Cut
Burst On
Burst Off
*
Fuzzy
D/N Level Low
D/N Level High
Burst On
Burst Off
*
AGC
Off
18dB
26dB
30dB
*
32dB
34dB
Sens Up
36dB
22dB
R-Gain
B-Gain
2500K ~ 9500K *
2000K ~ 18000K
WB - Auto *
WB - Menu
WB - Push
White Bal
NU
Set up Menu
Sync
Int
Shutter
Lens
BLC
Configur
White B
Cam Tit
D/N
1/50
Bright
Off
e
Aperture
al
AWB
le
Off
Fuzzy
RS-485
Address
Exit
Reset
Quit
TOP ME
SECOUND MENU
THIRD MENU
BF
Lens
Bright
Configure
Chroma
Level
Pedestal
Level
Aperture
H-APT Level
el
V-APT Lev
Sync
INT
*
LL
V-Phase
BLC
Off
*
Center 1
Center 2
Door Way 1
Up Half
Low Half
Level
Door Way 2
Gamma
0.45
*
0.8
1
RS485
Address _ _ _
B-Rate
9600dps
*
Address
4800dps
Password Setting
Password _ _ _
Shutter
AES
1/2K
1/60(1/50)
*
1/100(1/120)
1/250
1/500
1/1K
1/2K
1/4K
1/10K
Bright
1/5K
1/10K
1/20K
1/50K
*
1/100K
Text
CAM Tilte
Position
Off
*
On
D/N
IR Pass
IR Cut
Burst On
Burst Off
*
Fuzzy
D/N Level
Low
D/N Level
High
Burst On
Burst Off
*
AGC
Off
18dB
26dB
30dB
*
32dB
34dB
Sens Up
36dB
22dB
R-Gain
B-Gain
2700K ~ 9100K
*
2500K ~ 15000K
WB
- Auto *
