DEVI Devireg 330 Installation And Use Instructions Manual Download Page 8

Austalian Warranty Certificate

The following Warranty is provided by DEVI Heating
Systems ABN 39 898 434 262, herein after referred to
as DEVI. It is offered in addition to any relevant statutory
Federal or State Warranty.
DEVI is a partner of the DEVI Group of Companies, who
are a Danish based specialist heating product
manufacturer.
DEVI A/S Denmark is a member of the European Group
of Supplier's, and is at all times subject to EEC general
product liability rules.

DEVI warrants deviflex® heating cables for a period of
TEN (10) YEARS from the date of purchase and all other
DEVI products for a period of TWO (2) YEARS, from the
date of purchase.

DEVI warrants its products against defects in
manufacture, material, or workmanship. Proof of
purchase must be provided. Installations must be carried
out in accordance with the instructions supplied, and by
accredited installers.

An authorized DEVI representative must be given the
opportunity to inspect and report on any defects.

The obligation of DEVI, under this warranty, is to repair or
replace any product, which, within the above stated time
periods, is found to our satisfaction to be defective, free of
charge to the customer. However, the labour cost for
removing and/or refitting any product will be at the
customer's expense.  In the case of any removable
products such as Thermostats, these are to be returned
to the place of purchase, or to DEVI Sydney, where DEVI
reserves the right to repair or replace the unit at no
charge or unreasonable delay to the customer.

Summary of Contents for Devireg 330













Reviews: