manualshive.com logo in svg

DEVA Broadcast DB3010, Maintenance And Operating Manual

Share
Download
DEVA Broadcast DB3010 Maintenance And Operating Manual Download Page 45

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria

Tel: +359 56 820027, Fax: +359 56 836700

E-mail: [email protected] ,Web: www.devabroadcast.com

- 45 -

Alarms

Alarm notifications 

[E-mail] – global enable/disable E-mail notification; 

[SNMP] – global enable/disable SNMP notification; 

[GPO] – global enable/disable GPO actions. 

NOTE:

 If the monitoring option is disabled, notifications will not be sent, nevertheless whether 

they are enabled or disabled. 

RF, FM Left Audio, FM Right Audio, IP Left Audio, IP Right Audio Alarms

The settings applied to these alarms - are identical and are explained in details below.

Range

 – interactive slider used to adjust the 

Low & High thresholds

 at which an alarm will be 

generated; 

Thresholds

 –sets the desired 

Low & High thresholds

 (as explained above) but in figures.

Trigger Time

 – waiting time before active alarm is generated; 

Release Time

 – waiting time before idle alarm is generated; 

Summary of Contents for DB3010



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands