2.1
CODES AND STANDARDS
Follow all national and local codes and standards in ad-
dition to these instructions. The installation must comply
with regulations of the serving gas supplier, local build-
ing, heating, plumbing, and other codes. In absence of
local codes, the installation must comply with the national
codes listed below and all authorities having jurisdiction.
In the United States and Canada, follow all codes and
standards for the following:
2.1.1
Safety
USA
: National Fuel Gas Code (NFGC) NFPA 54-
2009/ANSI Z223.1-2009 and the Installation Stan-
dards, Warm Air Heating and Air Conditioning Systems
ANSI/NFPA 90B
CANADA
: National Standard of Canada, Natural Gas
and Propane Installation Code (NSCNGPIC) CAN/CSA
B149.1-2010
2.1.2
General installation
USA
: NFGC and the NFPA 90B. For copies, contact
the National Fire Protection Association Inc., Battery
march Park, Quincy, MA 02269; or for only the NFGC
contact the American Gas Association, 400 N. Capitol,
N.W.,Washington DC 20001
CANADA
: NSCNGPIC. For a copy, contact Standard
Sales, CSA International, 178 Rexdale Boulevard, Eto-
bicoke (Toronto), Ontario, M9W 1R3, Canada
2.1.3
Combustion and and air ventilation
USA
: Section 9.3 of the NFPA54/ANSI Z223.1-2009 Air
for Combustion and Ventilation
CANADA
: Part 8 of the CAN/CSA B149.1-2010, Venting
Systems and Air Supply for Appliances
2.1.4
Duct systems
USA and CANADA
: Air Conditioning Contractors Asso-
ciation (ACCA) (Manual D), Sheet Metal and Air Condi-
tioning Contractors National Association (SMACNA), or
American Society of Heating, Refrigeration, and Air Con-
ditioning Engineers (ASHRAE).
2.1.5
Acoustical lining and fibrous glass
duct
USA and CANADA
: current edition of SMACNA, NFPA
90B as tested by UL Standard 181 for Class I Rigid Air
Ducts.
2.1.6
Gas piping and pipe pressure testing
USA
: NFPA 54/ANSI Z223.1-2009 NFGC; Chapters 5, 6,
7, and 8 and national plumbing codes.
CANADA
: CAN/CSA-B149.1-2010, Part 6
IN THE STATE OF MASSACHUSETTS:
• This product must be installed by a li-
censed plumber of gas fitter;
• When flexible connectors are used, the
maximum length shall not exceed 36 in.
(914 mm);
• When lever type gas shutoffs are used
they shall be ”T” handle type;
• The use of copper tubing for gas pip-
ing is not approved by the state of Mas-
sachusetts;
2.1.7
Electrical connections
USA
: National Electrical Code (NEC) ANSI/NFPA 70-
2011
CANADA
: Canadian Electrical Code
2.2
ELECTROSTATIC DISCHARGE
CAUTION
FURNACE RELIABILITY HAZARD
Failure to follow this caution may result in unit
component damage. Electrostatic discharge can
affect electronic components. Take precautions
during furnace installation and servicing to pro-
tect the furnace electronic control. These precau-
tions will help to avoid exposing the control to
electrostatic discharge by putting the furnace, the
controls, and the technician at the same electro-
static potential.
1. Disconnect all power to the furnace. Multiple dis-
connects may be required.
DO NOT TOUCH
THE CONTROL OR ANY WIRE CONNECTED
TO THE CONTROL PRIOR TO DISCHARGING
YOUR BODY’S ELECTROSTATIC CHARGE TO
GROUND.
2. Firmly touch the clean, unpainted, metal surface of
the furnace chassis which is close to the control.
Tools held in a person’s hand during grounding will
be satisfactorily discharged.
3. After touching the chassis, you may proceed to ser-
vice the control or connecting wires as long as you
11
Summary of Contents for Chinook C105-M-V
