Detex DSI DS500 Service & Installation Manual Download Page 8

Page: 8 / 27

Use in concrete ONLY. Not recommended for use in lightweight masonry such as block or brick.

Warning!

Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors.

Caution: Use of core drills is not recommended to drill holes for use with this anchor.

The use of carbide drill bits manufactured with ANSI B212.15 drill bit diameter requirements is recommended for installation of this anchor.

Anchor spacing and edge distance (anchor installation locations) are the responsibility of the engineer of record.

Installing product in oversized holes is not recommended. Product will not set properly or achieve full designed load in oversized holes.

* Setting torque only applies at the time of installation.

Select a carbide drill bit with a diameter equal to the anchor diameter. Drill hole at least 1/4” deeper than nominal anchor embedment.

Clean hole with pressurized air or vacuum to remove any excess dust/debris.

Using the washer and nut provided, assemble the anchor, leaving nut one half turn from the end of anchor to protect threads. Drive

Wedge Type Concrete Anchor Instructions

512-321-4426

INS-DS500-190401

Designed Security, Inc - 1402 Hawthorne Street, Bastrop Texas 78602 - (800) 272-3555

[email protected]

Summary of Contents for DSI DS500




























Search results

Summary of Contents for DSI DS500

Reviews:

Related manuals for DSI DS500

Brands by name

Popular brands

Detex DSI DS500, Service & Installation Manual

Search results

Summary of Contents for DSI DS500

Reviews:

Related manuals for DSI DS500

Brands by name

Popular brands