OUTSIDE
LEVER
KEY
①
②
5A:
Insert control key,
turn approximately 10
degrees, then pull out
the IC core.
5B:
(If required)
Insert push pin to
depress the catch and
pull off the outside lever.
PUSH PIN
HOLE
③
SPRING FOR
6-PIN IC CORE,
REMOVE IT FOR
7-PIN IC CORE.
IC CORE
①
②
OUTSIDE
LEVER
5C:
Install lever and IC
core with the control key.
①
②
5D:
Turn the key approximately
10 degrees counter clockwise
and then remove the control key.
Right keyway direction
after installing IC core.
Keep the control key
in a secure location
and use the normal
key for daily operation.
TEMPLA
TE
FOR
INST
ALLING
C
L
LA
TCH
DETACH
HERE
HIGH
BEVEL
FLA
T NO
BEV
EL
HIG
H
BEVE
L
LOW
BEVE
L
LOW
BEVE
L
BACKSET
BACKSET
8
LA
TC
H
8
1
MA
RK
CENT
ER
FO
R
HO
LE
Notch
for
metal
door
only
3
DR
1
4
5
32
5
32
IMP
OR
TA
NT
1.
FOR
H
IGH
SID
E OF
B
EV
EL
P
LA
CE
OU
TS
ID
E LIN
E
AT
E
DGE
OF
D
OOR
2.
FOR
FLA
T D
OOR
S P
LA
CE
C
EN
TE
R
LIN
E
AT
E
DGE
OF
D
OOR
3.
FOR
LOWS
ID
E OF
B
EV
EL
P
LA
CE
IN
SID
E LIN
E
AT
E
DGE
OF
D
OOR
DR
1
3
8
MA
RK
CENT
ER
O
F
DO
O
R
T
HI
CKNES
S
FO
R 1
″
D
IA
HO
LE
C
L
C
L
2
34
MA
RK
C
EN
TE
R
FOR
3/8"
H
OLE
S
NOTE
:
Do
not
drill
these
holes
for
non
thr
u bolt
installation.
DH706D471CL
INSIDE
SPRING CAGE
INSIDE
ROSE
TURN
AND
PULL
PUSH PIN
HOLE
INSIDE
LEVER
2G:
Slide lever onto spindle.
Push lever completely into place.
(Pull on lever to make sure that
catch is fully engaged).
2E:
Remove inside
lever using push pin.
INSIDE
LEVER
PUSH PIN
CATCH
①
②
INSIDE
ROSE
2F:
Install inside rose and make sure inside
rose and inside spring cage are tightened.
IMPORTANT
CATCH
If the door is thicker
than 2",the catch will
be covered by inside
rose, do not install
inside lever and lock.
INSIDE
SPRING
CAGE
Align dimples on
rose with rectangular
hole in spring cage.
Push in rose until
dimples snap into
rectangular hole.
INSTRUCTIONS FOR ADJUSTING LOCK TO FIT DOOR THICKNESS OTHER THAN 1-3/4"
POST
LOCK BODY
6A:
Unscrew two
posts in lock body
by screwdriver.
6C:
Screw two posts
back in so they hold the
outside rose tightly.
JOINT
BLADE
Oppose joint
blade to catch.
CENTER LINE
OUTSIDE
TRIM
6B:
Adjust outside trim according
to the door thickness, make sure the
lock body at both sides is symmetrical.
Catch can not
be covered
by rose.
2D:
Slide inside lever onto spindle and
check to see if the rotation is smooth.
Adjust the radial clearance between inside
spring cage and inside lever if necessary.
INSIDE
LEVER
INSTRUCTIONS FOR REMOVING AN INSTALLED
LOCK FROM THE DOOR
4
Unclench by
screwdriver
4B:
Remove inside
rose by turning and pulling off.
4C:
Remove mounting
screw with screwdriver
and inside spring cage.
6
4A:
Insert push pin into hole to
depress catch and remove the lever.
3
INSTALL STRIKE
STRIKE
DOOR
JAMB
CENTER LINE
After door is closed,
deadlocking plunger
is retracted.
LATCH
STRIKE BOX
5
INSTRUCTIONS FOR IC CORE AND LEVER
REPLACEMENT (If Required)
For thickness which
is not 1-3/4", first step
remove outside lever
(refer to step 5A & 5B
above), then follow the
steps 6A,6B,6C,6D,6E
for adjusting.
SPRING FOR
6-PIN IC CORE,
REMOVE IT FOR
7-PIN IC CORE.
IC CORE
①
②
OUTSIDE
LEVER
6D:
Install lever and IC
core with the control key.
①
②
6E:
Turn the key approximately
10 degrees counter clockwise
and then remove the control key.
T93797_A
2/2
Design Hardware is a trademark of dormakaba USA Inc. ©2021 All rights reserved.
Template to scale 1 : 1, full size.
