manualshive.com logo in svg

Design Dynamics VTD-18N-JHB, Owner'S Operation And Installation Manual

Share
Download
Design Dynamics VTD-18N-JHB Owner'S Operation And Installation Manual Download Page 9

www.desatech.com

114370-01E

9

INSTALLATION

Continued 

4.. Place. log. set. assembly. in. center. of.

fireplace. floor.. Make. sure. front. faces.

forward.

5.. Install.gas.connector.tube.into.gas.supply.

fitting. Carefully shape tube to attach to 
adapter fitting being careful not to kink 

tube.

6.. Install. provided. gas. connector. tube.

into the gas inlet fitting (see Figure 7, 
page 8).

7.  Test for leaks following instructions under 

Testing Burner for Leaks

.

Repositioning Gas Inlet to Left Side of 

Unit

1.  Remove venturi and gasket by unscrew

-

ing  two  screws  under  chassis  (see 
Figure 8).

2.  Unthread  elbow  fitting  from  orifice  (see 

Figure 8).

3.  Remove orifice and brackets by unscrew

-

ing two screws on right side of unit (see 
Figure 8).

4.  Install orifice and brackets into left side of 

unit using screws removed in step 1.

5.. Install. venturi. and. gasket. under. bottom.

burner and into repositioned orifice and 
brackets (see Figure 8).

6.  Thread elbow fitting back into orifice. Ap

-

ply thread sealant to orifice threads (see 
Figure 8).

7.. Install. gas. connector. tube. that. comes.

with  log  set  into  gas  inlet  fitting  (see 
Figure 8).

8.  Install supplied brass adapter fitting that 

comes  with  log  set  into  fireplace  gas 

supply. pipe.. Use. thread. sealant. (see.

Figure 8).

9.. Place. log. set. assembly. in. center. of.

fireplace. floor.. Make. sure. front. faces.

forward.

10..Install.gas.connector.tube.into.gas.supply.

fitting. Carefully shape tube to attach to 
adapter  fitting.  Be  careful  not  to  cause 

kinks.in.tube.

11. Test for leaks following instructions under 

Testing Burner for Leaks

.

TESTING BURNER FOR LEAKS

1.. Generously.apply.noncorrosive.leak.de-

tection fluid to all connections.

 WARNING: Never check for 

gas leaks with open flame.

2.  Light  burner  with  shutoff valve  no more 

than. half. open. and. holding. a. match.
slightly.in.front.of.the.pan.(see.

Lighting 

Instruction

s

, page 10).

3.  Inspect all connections for bubbles, raw 

gas odors, or flame from any area other 
than  burner.  If  leaks  are  detected,  shut 

off. gas. valve. immediately.. Tighten. or.
reassemble.the.loose.connections.using.

pipe joint compound until burner system 

is.leak.free.

4.  When  finished  testing,  turn  gas  shutoff 

valve OFF to extinguish all flames.

Figure 8 - Repositioning Gas Inlet to Left 

Side of Unit

Outer.
Bracket

Gasket

Venturi

Screws

Inner.
Brackets

Orifice

Elbow 

Fitting

Elbow 

Fitting

Inner.Brackets

Orifice

Gasket

Venturi

Screws

Chassis

Chassis

Summary of Contents for VTD-18N-JHB

















Reviews:

No comments

Brands by name

Popular brands

Load more brands