background image

Repair/Return Form

                 (Please make copy)                   

 

Please fill out and enclose this form when shipping items for service.  Pack items carefully! 

 
Customer Name_________________________________   Date___________ 
Address________________________________________________________ 
City______________________ State______ Zip_________ Country________  
Phone #_________________   Cell #__________________  
Email _________________________ 
 
Items in Box:  
DA35 Serial #__________ DA50 Serial #__________ DA60 Serial #__________  
DA70 Serial #__________ DA85 Serial #__________ DA100 Serial #_________ DA100i Serial 
#________  DA120 Serial #_________ DA150 Serial #_________  DA170 Serial #_________ 
DA200 serial #_________  Other________________  
 
Single Ignition Serial # ________           Twin Ignition Serial # ________ 
 

(Below items normally not required to repair or test the engine) 
 

Prop Bolts? ___________                Standoffs? ____________ 
Prop washer? _________                 Muffler(s)? ____________    
Muffler screws_________                Other Items? __________ 
 
 
REASON FOR ENGINE AND/OR IGNITION RETURN?  
Crash: Yes____  No____       Other_________________________________________ 
________________________________________________________________________________
________ 
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________ 
 
Prop used? ______________                 Oil used?   _____________ 
Gas type?  _____________                     Exhaust system type? __________________ 
 
Has the engine been sent in for service before?   _______Why?________________  
______________________________________________________________________ 
______________________________________________________________________

 

 

 

 

DESERT AIRCRAFT 

1815 S. Research Loop 
Tucson, AZ  85710 
520 722 0607 
[email protected] 
www.desertaircraft.com                                                                                  

    

Modellmarkt24.ch

Summary of Contents for DA35











Reviews: