Desa VTGF33NR Owner'S Operation And Installation Manual Download | Manualshive

Page: 1 / 50

background image

UNVENTED (VENT-FREE) GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

Save this manual for future reference.

Save this manual for future reference.

For more information, visit www.desatech.com

For more information, visit www.desatech.com

Shown with optional cabinet mantel,

hearth base, and trim accessories.

WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any
other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a quali-

fied installer, service agency, or the gas supplier.

WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual for correct installation and
operational procedures. For assis-
tance or additional information con-
sult a qualified installer, service
agency, or the gas supplier.

WARNING: This is an unvented gas-
fired heater. It uses air (oxygen)
from the room in which it is in-
stalled. Provisions for adequate
combustion and ventilation air must
be provided. Refer to

Air for Com-

bustion and Ventilation section on
page 5 of this manual.

CGEFP33PR, CGEFP33NR, EFP33PR, EFP33NR,

VTGF33NR, and VTGF33PR

Gas Fireplace with Total Control System (TCS)

This appliance may be installed in an aftermarket,* permanently located, manufactured
(mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance
is not convertible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Shown with optional hearth

base accessory.

TM

1
2
3
...
»

Summary of Contents for VTGF33NR



















































Reviews:

No comments

Related manuals for VTGF33NR

Brand: TermaTech Pages: 52

Brand: Majestic Pages: 44

Brand: Napoleon Pages: 128

Sovereign Series

Brand: Majestic Pages: 24

astria Mission Mission42TMN

Brand: IHP Pages: 32

Brand: Allen + Roth Pages: 40

Brand: Northline Express Pages: 35

Brand: Bronpi Pages: 81

Slimfocus mural

Brand: Focus Pages: 8

Brand: Kingsman Pages: 13

COLORADO DELUXE

Brand: Wamsler Pages: 80

Brand: Iso Pages: 2

Brand: Jocel Pages: 22

Brand: Element4 Pages: 56

Brand: Heat&Glo Pages: 61

Brand: lifeSMART Pages: 18

Brand: Nibe Pages: 20

Brand: Kohl's Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands