background image

8

102590

!

CAUTION

Disconnect heater from propane supply tank(s).

STORAGE

1. Store propane tank(s) in safe manner. Follow all local codes. Always store

propane tanks outdoors.

2. Store in dry, clean, and safe place. Do not store hose/regulator assembly inside

heater combustion chamber.

3. When taking heater out of storage, always check inside of heater. Insects and

small animals may place foreign objects in heater. Keep inside of heater free
from combustible and foreign objects. Remove motor and other internal parts
if needed to remove foreign objects (see Service Procedures, page 10).

MAINTENANCE

1. Keep heater clean. Clean heater annually or as needed to remove dust and

debris. If heater is dirty or dusty, clean heater with a damp cloth.

2. Inspect heater before each use. Check connections for leaks. Apply mixture of

liquid soap and water to connections. Bubbles forming show a leak. Correct all
leaks at once.

3. Inspect hose/regulator assembly before each use. If hose is highly worn

or cut, replace.

4. Have heater inspected yearly by service person.
5. Keep inside of heater free from combustible and foreign objects. Remove

motor and other internal parts if needed to clean inside of heater (see Service
Procedures,
 page 10).

6. Clean fan every 500 hours of operation or as needed.

!

WARNING

Never service heater while it is plugged in, connected to
propane supply, operating, or hot. Severe burns and
electrical shock can occur.

P

i

e
z
o

Power

Cord

Motor

L1

L1

L2

L2

L2

L1

Solenoid

Valve

Thermal

Switch

L1

L2

Shell

Automatic

Control Valve

Thermocouple

Figure 6 - Wiring Diagram

WIRING

DIAGRAM

Summary of Contents for SH10E

















Reviews: