background image

www.desatech.com

118621-01B

6

DETERMINING FRESH-AIR FLOW 
FOR HEATER LOCATION

Determining if You Have a Confined or 
Unconfined Space

Use this work sheet to determine if you have a 
confined or unconfined space.

Space:

 Includes the room in which you will install 

heater plus any adjoining rooms with doorless 
passageways  or  ventilation  grills  between  the 
rooms.
1.  Determine the volume of the space (length 

x width x height).

 

Length x Width x Height =__________cu. ft. 
(volume of space)

 

Example:

 Space size 20 ft. (length) x 16 ft. 

(width) x 8 ft. (ceiling height) = 2560 cu. ft. 
(volume of space)

 

If  additional  ventilation  to  adjoining  room 
is supplied with grills or openings, add the 
volume of these rooms to the total volume 
of the space. 

2.  Multiply the space volume by 20 to determine 

the maximum Btu/Hr the space can support.

 

  ______ (volume of space) x 20 = (Maximum 
Btu/Hr the space can support)

 

Example:

 2560 cu. ft. (volume of space) x 20 = 

51,200 (maximum Btu/Hr the space can sup-
port)

3.  Add the Btu/Hr of all fuel burning appliances 

in the space.

 

Vent-free heater 

 ____________ Btu/Hr

 

Gas water heater*   ____________ Btu/Hr

 

Gas furnace 

 ____________ Btu/Hr

 

Vented gas heater   ____________ Btu/Hr

 

Gas fireplace logs   ____________ Btu/Hr

 

Other gas appliances* + ___________ Btu/Hr

 

Total 

= ___________ Btu/Hr

 

* Do not include direct-vent gas appliances. 
Direct-vent  draws  combustion  air  from  the 
outdoors and vents to the outdoors.

 

Example:

 

Gas water heater    ____________ Btu/Hr

 

Vent-free heater 

+  ___________ Btu/Hr

 

Total 

=  ___________ Btu/Hr

AIR FOR COMbUSTION 

AND VENTILATION

Continued

4.  Compare  the  maximum  Btu/Hr  the  space 

can support with the actual amount of Btu/Hr 
used.

 

  _______ Btu/Hr (maximum can support)

 

  _______ Btu/Hr (actual amount used)

 

Example:

 

51,200 Btu/Hr (maximum can support) 

 

60,000 Btu/Hr (actual amount used)

The space in the above example is a confined 
space because the actual Btu/Hr used is more 
than  the  maximum  Btu/Hr  the  space  can  sup-
port. You must provide additional fresh air. Your 
options are as follows:
A.  Rework worksheet, adding the space of an 

adjoining room. If the extra space provides 
an unconfined space, remove door to adjoin-
ing  room  or  add  ventilation  grills  between 
rooms.  See 

Ventilation  Air  From  Inside 

Building

, page 7.

B.  Vent  room  directly  to  the  outdoors.  See 

Ventilation Air From Outdoors

, page 7.

C.  Install a lower Btu/Hr heater, if lower Btu/Hr 

size makes room unconfined.

If the actual Btu/Hr used is less than the maxi-
mum Btu/Hr the space can support,

 

the space is 

an unconfined space. You will need no additional 
fresh air ventilation.

  WARNING:  If  the  area  in 

which the heater may be oper

-

ated is smaller than that defined 

as an unconfined space or if the 

building  is  of  unusually  tight 

construction, provide adequate 

combustion and ventilation air 

by one of the methods described 

in the 

National Fuel Gas Code, 

ANSI Z223.1/NFPA 54 Section 5.3 

or applicable local codes.

  40,000
  20,000
  60,000

Summary of Contents for NZ100

































Reviews: