background image

103615

5

5

OPERATION

 WARNING: Review and understand the warnings

in the Safety Information Section. They are needed to
safely operate this heater. Follow all local codes
when using this heater.

TO START HEATER

1.

Follow all ventilation and safety information.

2.

Fill fuel tank with kerosene or No. 1 fuel oil.

3.

Attach fuel cap.

4.

Plug power cord of heater into standard 230 volt/50 hertz,
grounded (earthed) outlet. Use an extension cord if needed.
Use only a three-prong, grounded (earthed) extension cord.

Extension Cord Wire Size Requirements

Up to 30.5 meters (100 feet) long, use 1.0 mm

(16 AWG) conductor

30.6 to 61 meters (101 to 200 feet) long, use 1.5 mm

(14 AWG)

conductor

Push ON/OFF switch to ON and heater should start. If heater does
not start, press flame-out control reset button (see Figures 5 and 6).

TO STOP HEATER

Push ON/OFF switch to OFF.

TO RESTART HEATER

1.

Wait 2 minutes after stopping heater.

2.

Repeat steps under To Start Heater.

Flame-Out
Control
Reset Button

ON/OFF
Switch

Figure 5 - Flame-Out Control Reset Button, 35/70,000 Btu/Hr

Figure 6 - Flame-Out Control Reset Button, 100/150,000 Btu/Hr

Flame-Out Control
Reset Button

ON/OFF
Switch

STORING, TRANSPORTING,
OR SHIPPING

Note:

 If shipping, transport companies require fuel tanks to be empty.

1.

Drain fuel tank.

Note:

 Some models have drain plug on underside of fuel tank.

If so, remove drain plug to drain all fuel. If heater does not
have drain plug, drain fuel through fuel cap opening. Be sure
all fuel is removed.

2.

Replace drain plug if provided.

3.

If any debris is noted in old fuel, add 1 or 2 quarts of clean
kerosene to tank, stir, and drain again. This will prevent ex-
cess debris from clogging filters during future use.

4.

Replace fuel cap or drain plug. Properly dispose of old and
dirty fuel. Check with local automotive service stations that
recycle oil.

5.

If storing, store heater in dry place. Make sure storage place is
free of dust and corrosive fumes.

IMPORTANT:

 Do not store kerosene over summer months for use

during next heating season. Using old fuel could damage heater.

OPERATION

STORING, TRANSPORTING, OR SHIPPING

Summary of Contents for Master B100CEB

























Reviews: