background image

10

107297

INFRARED PROPANE/LP GAS HEATER

Tee Joint

Reducer
Bushing to
1/8" NPT

1/8" NPT
Plug Tap

Test
Gauge
Connection *

Sediment
Trap

Tee Joint

Pipe Nipple

Cap

Equipment
Shutoff
Valve *

3/8" NPT
Pipe Nipple

Heater
Cabinet

Figure 15 - Gas Connection

*  A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable
alternative to test gauge connection. Purchase the optional CSA/AGA design-certified
equipment shutoff valve from your dealer. See Accessories, page 19.

3" Minimum

Ground Joint
Union

Pressure
Regulator

Regulator
Bracket

Inlet Pipe From
External Regulator
(11" W.C. to 14"
W.C. Pressure)

CONNECTING TO GAS
SUPPLY

 WARNING: A qualified service

person must connect heater to
gas supply. Follow all local codes.

Typical Inlet Pipe Diameters

FB-3B/FBS-3C

3/8" or greater

FB-5B/FBS-5C

1/2" or greater

Installation must include equipment shutoff
valve, union, and plugged 1/8" NPT tap.
Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from
heater (see Figure 15).

IMPORTANT:

 Install an equipment shutoff

valve in an accessible location. The equip-
ment shutoff valve is for turning on or
shutting off the gas to the appliance.

Install sediment trap in supply line as shown
in Figure 15. Locate sediment trap where it
is within reach for cleaning. Locate sedi-
ment trap where trapped matter is not likely
to freeze. A sediment trap traps moisture
and contaminants. This keeps them from
going into heater controls. If sediment trap
is not installed or is installed wrong, heater
may not run properly.

IMPORTANT:

  Hold pressure regulator

with wrench when connecting it to gas pip-
ing and/or fittings.

 CAUTION: Use pipe joint seal-

ant that is resistant to liquid pe-
troleum (LP) gas.

The installer must supply an external regu-
lator. The external regulator will reduce
incoming gas pressure. You must reduce
incoming gas pressure to between 11 and 14
inches of water. If you do not reduce incom-
ing gas pressure, heater regulator damage
could occur. Install external regulator with
the vent pointing down as shown in Figure
14. Pointing the vent down protects it from
freezing rain or sleet.

 CAUTION: Never connect

heater directly to the propane/
LP supply. This heater requires
an external regulator (not sup-
plied). Install the external regu-
lator between the heater and
propane/LP supply.

 CAUTION: Use only new, black

iron or steel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check your local
codes. Use pipe of large enough
diameter to allow proper gas vol-
ume to heater. If pipe is too small,
undue loss of pressure will occur.

INSTALLATION

Continued

Figure 14 - External Regulator with Vent
Pointing Down

Propane/LP
Supply
Tank

Vent Pointing Down

External Regulator

Apply pipe joint sealant lightly to male
threads. This will prevent excess sealant
from going into pipe. Excess sealant in pipe
could result in clogged heater valves.

 WARNING: This appliance re-

quires a 3/8" NPT (National Pipe
Thread) inlet connection to the
pressure regulator.

Summary of Contents for FBS-3B





























Reviews: