background image

11

101827

INSTALLING HEATER TO WALL

Mounting Bracket

The mounting bracket is located on back panel of heater. It has been taped there for
shipping. Remove mounting bracket from back panel.

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These
two holes are 16 inches apart from their centers. Attach mounting bracket to wall in
one of two ways.

1. Attaching to wall stud
2. Attaching to wall anchor

Attaching to wall stud 

  This method provides the strongest hold. Insert mounting

screws through mounting bracket and into wall studs.

Attaching to wall anchor   

This method allows you to attach mounting bracket to

hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure
hold for the mounting bracket.

Figure 6 - Removing Front Panel Of Heater

Removing Front Panel Of Heater

1. Remove two screws near bottom corners of front panel.
2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".
3. Pull bottom of front panel forward, then down.

Mounting Bracket

INSTALLING

TO WALL

Continued

C o n t i n u e d

Summary of Contents for Comfort Glow CGP16RA

































Reviews: