![background image](http://html1.mh-extra.com/html/desa/comfort-glow-cf26nr/comfort-glow-cf26nr_owners-operation-and-installation-manual_2486301018.webp)
105443-01E
For more information, visit www.desatech.com
For more information, visit www.desatech.com
18
OPERATING FIREPLACE
Optional Remote Operation
OPTIONAL REMOTE
OPERATION
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, page 31). Follow instructions included
with the remote control.
Thermostat Control Operation
(Optional CGHRCTA Series Only) The thermostat control
setting on the remote control unit can be set to any comfort level
between HI and LO. The burner will turn on and off automati-
cally to maintain the comfort level you select. The ideal comfort
setting will vary by household depending upon the amount of
space to be heated, the output of the central heating system, etc.
OPERATING FIREPLACE
Continued
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions on page 17.
1.
After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjust-
ment knob anywhere between HI and LO. Slide the selec-
tor switch to the REMOTE position.
NOTE:
The burner
may light if hand-held remote ON button was on when se-
lector switch was last turned off. You can now turn the
burner on and off with the hand-held remote control unit.
IMPORTANT:
Do not leave the selector switch in the
REMOTE position when the pilot is not lit. This will drain
the battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
Figure 34 - Setting the Selector Switch, Control Knob, and
Flame Adjustment Knob for Remote Operation
Selector Switch in Remote Position
(Optional Remote Control)
ON
OFF
REMOTE
O
FF
PILO
T
O
N
L O
I H
Control Knob
in On Position
Flame
Adjustment Knob
CGHRC Series Operation:
2a. Press the ON/OFF button to turn the burner on and off.
When turning burner off, the pilot will remain lit.
CGHRCTA Series Operation
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 35). The lights to the left of the button
will show AUTO, ON, or OFF.
• In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
IMPORTANT:
This remote control has been specially en-
gineered to take an air temperature sample every 5.5
minutes in the auto mode. It will not respond immedi-
ately to the temperature setting being turned up or down.
IMPORTANT:
The hand-held remote control unit must
be near the heater. Do not keep the hand-held remote
control unit too close to the heater. The thermostat on
the hand-held remote control unit will heat up too quickly
and turn the heater off.
3.
To turn the burner off, press the AUTO/ON/OFF button
until OFF lights. The pilot will remain lit.
IMPORTANT:
To turn the pilot off, manually turn the con-
trol knob on the heater to the OFF position.
Figure 35 - Thermostat Hand-Held Remote Control Unit
Selections (CGHRCTA Series only)
Shows Temperature
Setting
The Log Heater will
Automatically Cycle
between Pilot and
the Heat Setting
that has been
Selected
Increases Room
Temperature in
AUTO Mode
Decreases Room
Temperature in
AUTO Mode
Turns Burners On
or Off and Allows
You to Choose the
Auto Setting