background image

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

®

CHDV34(N/P)(A)

Save this manual for future reference.

FOR YOUR SAFETY

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the fire

department.

WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual for correct installation and
operational procedures. For as-
sistance or additional information
consult a qualified installer, ser-
vice agency, or the gas supplier.

This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by
state or local codes.
*

 Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.

— Installation and service
must be performed by a
qualified installer, service
agency, or the gas supplier.

— This appliance is for use
only with indicated gas type. It
is not convertible for use with
other gases, unless a certified
kit is used.

Summary of Contents for CHDV34(N/P)(A)







































Reviews: