background image

CD32M (-1)(-2), CD36M (-A1)(-A2), CD42M-A

FOR YOUR SAFETY

WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the fire

department.

SAVE THIS BOOK

This book is valuable. In addition to instructing you on
how to install and maintain your appliance, it also con-
tains information that will enable you to obtain replace-
ment parts or optional accessory items when needed.
Keep it with your other important papers.

WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result caus-
ing property damage, personal injury, or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.

Save this manual for future reference.

Save this manual for future reference.

For more information, visit www.desatech.com

For more information, visit www.desatech.com

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND
INSTALLATION MANUAL

WARNING: This direct-vent gas fire-
place is intended for use with natural
or propane/LP gas only. Do not at-
tempt to burn any solid fuels in this
appliance.

WARNING: Improper installation, ad-
justment, alteration, service, or mainte-
nance can cause injury or property
damage. Refer to this manual for cor-
rect installation and operational proce-
dures. For assistance or additional in-
formation consult a qualified installer,
service agency, or the gas supplier.

This fireplace is manufactured for Stylecrest Inc. under the Coleman brand name by DESA.

This fireplace may be installed as an OEM installation in a manufactured (mobile) home and
must be installed in accordance with the manufacturers instructions and the 

Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280 in the United States or the
Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This fireplace is only for use with
the type(s) of gas indicated on the rating plate. A conversion kit is supplied with the fireplace.

Summary of Contents for CD32M























Reviews: