will click into place. Note: To fully engage
the gearing mechanism, the position
adjustment knob may need to be rotated
slightly.
5. Adjusting the
orthosis position:
Rotate the position
adjustment knob (2)
until the joint’s soft
tissues are stretched
to patient tolerance. Note: See Patient
Protocol Card to determine the appropriate
amount of stress, and wearing time.
6. Getting more flexion: Remove the two
forearm cuff screws (4). Rotate the cuff
parallel to the axis of the arm, so that the
cuff opening is aimed upward, and replace
the screws. Trim all white Wire-Foam
™
trim
zones on the forearm and Biceps cuffs.
Note: Do not trim the soft foam liner. Retain
the trimmed trim zones in case they are
needed for extension assist.
7. Removing orthosis: Disengage the gearing
mechanism by pulling out the engagement
knob (1), and at the same time pivot the
position adjustment knob (2) toward the
back of the unit. The forearm should move
freely. Unfasten all straps.
8. Changing softgoods: Remove the four
screws on the biceps plate (3) to remove the
biceps cuff. Attach new biceps cuff. Remove
the two forearm cuff screws (4) to remove
the forearm cuff. Attach new forearm cuff.
CARE INSTRUCTIONS
Clean Wire-Foam
™
pads and exterior of hinge with
non-abrasive cleaner. Straps and blue liner may
be machine-washed. Air-dry liner and straps prior
to wearing.
PRECAUTION
Caution should be used if any of these conditions
exist: peripheral vascular disease, healing skin
wounds, severe spasticity, heterotrophic
ossification, and mild osteoporoses.
Manufacturer
DeRoyal
200 DeBusk Lane, Powell, TN 37849 U.S.A.
888.938.7828
865.938.7828
Authorized Representative
DeRoyal Europe, Ltd.
Virginia Road, Kells, County Meath Ireland
353.46.9280100
Part #1-4425
Revision 4 Revised 3/05
©2005 DeRoyal. All Rights Reserved.
5
will click into place. Note: To fully engage
the gearing mechanism, the position
adjustment knob may need to be rotated
slightly.
5. Adjusting the
orthosis position:
Rotate the position
adjustment knob (2)
until the joint’s soft
tissues are stretched
to patient tolerance. Note: See Patient
Protocol Card to determine the appropriate
amount of stress, and wearing time.
6. Getting more flexion: Remove the two
forearm cuff screws (4). Rotate the cuff
parallel to the axis of the arm, so that the
cuff opening is aimed upward, and replace
the screws. Trim all white Wire-Foam
™
trim
zones on the forearm and Biceps cuffs.
Note: Do not trim the soft foam liner. Retain
the trimmed trim zones in case they are
needed for extension assist.
7. Removing orthosis: Disengage the gearing
mechanism by pulling out the engagement
knob (1), and at the same time pivot the
position adjustment knob (2) toward the
back of the unit. The forearm should move
freely. Unfasten all straps.
8. Changing softgoods: Remove the four
screws on the biceps plate (3) to remove the
biceps cuff. Attach new biceps cuff. Remove
the two forearm cuff screws (4) to remove
the forearm cuff. Attach new forearm cuff.
CARE INSTRUCTIONS
Clean Wire-Foam
™
pads and exterior of hinge with
non-abrasive cleaner. Straps and blue liner may
be machine-washed. Air-dry liner and straps prior
to wearing.
PRECAUTION
Caution should be used if any of these conditions
exist: peripheral vascular disease, healing skin
wounds, severe spasticity, heterotrophic
ossification, and mild osteoporoses.
Manufacturer
DeRoyal
200 DeBusk Lane, Powell, TN 37849 U.S.A.
888.938.7828
865.938.7828
Authorized Representative
DeRoyal Europe, Ltd.
Virginia Road, Kells, County Meath Ireland
353.46.9280100
Part #1-4425
Revision 4 Revised 3/05
©2005 DeRoyal. All Rights Reserved.
5