background image

10

temperatures from 15-25° Celsius. This is not a failure on the batteries, but normal behavior.

Please notice: Even a fully charged battery will run out of power if the electric scooter is not used for a period.
Expect a fully charged battery to keep power between 90 and 120 days in off mode, before it is fully discharged. If
only partially charged, this period is lower.

Please make sure the battery does not get above 50° Celsius, or below minus 10° Celsius for a longer period. (e.g.
don

t leave the electric scooter in a hot car in summer, do not put battery into fire etc.) Low temperature (e.g.

subzero temperature) can damage the battery cells.

Keep the Electric scooter away from open flame or other sources of heat to prevent the battery from getting too
hot. Also make sure not to leave the electric scooter at freezing temperatures. Both heat and excessive cold can
cause the battery to discharge.

Only use original charger or an official replacement, as different batteries may require specific charger, and if
using other chargers, this could cause damage to the product.

Do not overcharge and discharge the battery.

Please make sure to charge the battery before it is completely out of power, to avoid damaging the battery cells.
(damaged battery caused by wrong handling are not covered by the warranty)

It is forbidden to disassemble battery package. This is only to be handled by official service repair centers and
professionals.

Bearings, Screws, brakes and Wheels

Your electric scooter is made up of moving parts, which in time, will be susceptible to wear and tear.

Bearings and screws:

The electric scooter has sealed and dustproof bearings so that no lubrication is required. Check the bearings for
wear at regular intervals to avoid unsafe riding. Do not jump on and off and do not apply excessive force
otherwise to avoid damage to the bearings. This is not a sports electric scooter.

Make sure that all screws are properly tightened to avoid unsafe situations.

Please check the screws regularly and tighten if they seem loose.

Brakes:

Check the brake for wear at regular intervals to avoid unsafe riding. Do not apply excessive force to avoid damage
to the brake.

Wheels:

Check the wheels for wear at regular intervals to avoid unsafe riding.

Electric scooters come with different wheels but can in general be separated into tires with inflatable inner tubes
and solid wheels.

For inflatable tires, please make sure to keep the right pressure, as hard tires will last longer.

If the wheel seems wobbly even after screws are tightened, the bearings might be worn
down and need replacement

WARNING

Please make sure to check that the steering system is correctly adjusted and that all connection

Summary of Contents for SEL-80130 MK2























Reviews: