Denver CAD-495, Instruction Manual

Page: 4 / 8

E4
B
A
B
A
Main unit
Rear of the front panel
Front panel
SEL
TA SEEK SEL
2 sec.
SEL LOUD SEL MASK DPI SEL RETUNE DSP SEL
TA SEEK SEL
2 sec.
SEL LOUD SEL MASK DPI SEL RETUNE DSP SEL
SEL
TA SEEK SEL
2 sec.
SEL
LOUD SEL
MASK DPI SEL RETUNE DSP SEL
SEL
TA SEEK SEL
2 sec.
SEL LOUD SEL MASK DPI SEL RETUNE DSP SEL
LOCAL/DX LOCAL
SEL STEREO SEL SEL SEEK
BEEP
VOL
VOL
STEREO/MONO STEREO SEL SEL SEEK
BEEP
SEL SEEK1 / SEEK 2 SEEK
BEEP
VOL
BEEP ON/OFF
SEL BEEP
VOL
TA SEEK SEL
2 sec.
SEL LOUD SEL MASK DPI SEL RETUNE DSP SEL
CD MULTI ON/OFF
SEL
MULTI
SEL MULTI
SEL MULTI
SEL
MULTI
SEL MULTI
VOL
TA SEEK SEL
2 sec.
SEL DSP ON MASK DPI SEL RETUNE SEL
POP M --- ROCK M --- CLASS M --- FLAT M --- DSP OFF
VOL
TA SEEK SEL RETUNE SEL MASK DPI SEL
2 sec.
RETUNE L / RETUNE S
VOL
TA SEEK SEL
2 sec.
SEL SEL MASK DPI SEL RETUNE DSP
SEL LOUD ON/OFF
VOL
TA SEEK SEL MASK DPI SEL
2 sec.
MASK DPI / MASK ALL
VOL
TA SEEK SEL
2 sec.
TA SEEK / TA ALARM
VOL
Detaching and attaching the front panel
The front panel of this unit can be detached in order to prevent the unit from
being stolen.
DETACHING THE FRONT PANEL
Before detaching the front panel, be sure to press the OFF button first.
Then press the button (15) and detach the panel by pulling it towards you
as illustrated.
Note:
Be sure not to drop the panel when detaching it from the unit.
Notes:
• Make sure that the front panel is the right way up when attaching it to the
unit as it cannot be attached upside down.
• Do not press the front panel hard against the unit when attaching it. It can
be easily attached by pressing it lightly against the unit.
• When you carry the front panel with you, put it in the supplied front panel
case.
• Do not press hard or give excessive pressure to the display window of the
front panel when attaching it to the unit.
OPERATION
1. POWER ON/OFF ( )
By pressing this key, the unit is on or off.
This unit is turned on by pressing any key.
2,3. FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/FADER / TA SEEK/MASK DPI/RETUNE/AUDIO DSP/LOUDNESS/
CD MULTI/BEEP/SEEK/STEREO/LOCAL (SEL)
Turning the VOL knob Right or Left (3), you can adjust VOL/BASS/TREB/BAL/FAD. To select other functions, press the VOL
(3) knob shortly until the desired functions is shown on the display. Figure 1 shows how control functions are selected using
the VOL knob.
Fig. 1 Selection of sound control functions
1. VOL 2. SEL 3. BAS 4. TRE 5. BAL 6. FAD
Turning the VOL knob Right or Left. Increase or decrease the volume by turning
VOL VOL
or
VOL VOL
. These buttons can be used
to adjust the BASS, TREBLE, BALANCE and FADER.
TA SEEK/TA ALARM (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
TA SEEK Mode or TA ALARM mode is selected by
VOL VOL
or
VOL VOL
.
- TA SEEK mode:
When newly turned station does not receive TP information for 5 sec., the radio retunes to next station which has not the
same station (PI) as the last station, but has the TP information.
In TA seek mode, the current station can be changed to the completely different station because the unit searches TP station
when the field strength of the current station is very weak, or the current station has no TP signal.
- TA ALARM mode:
Any automatic retune mode is not activated, just can hear Beep sound.
1 3 2 4 2 5 2 6 2 2
B
A
Front panel
Panel case
Front panel