background image

ENGLISH

7

!8

Stylus pressure adjustment dial

• Use this to adjust the stylus pressure.

!9

Counterweight

• Use this to balance the tone arm and to adjust the stylus

pressure.

@0

Tone arm lift

• This elevates the tone arm above the record surface.

@1

Extra stylus holder

• Place extra headshells here.

@2

45 rpm adaptor holder

• Place on the attached 45 rpm adaptor here.
• Push down the rear side of 45 rpm adaptor to take it.

@3

Voltage selector

• Check the voltage selector switch is set to an

appropriate voltage in your area before use.

@4

Dust cover

• Set the dust cover in place when not using the set to protect

the turntable from dust and dirt.

• The dust cover is not locked on the set.  Handle it with care.

@5

Output terminal (DIGITAL OUT)

@6

Output terminal (AUDIO OUT)

• Connect the included connecting cord here.  (See page 8.)

@7

Phono/Line selector (PHONO/LINE)

@8

Power terminal (AC IN)

• Connect the connector side of the included AC cord here.

(See page 8.)

@5 @6@7 @8

@4

Rear panel

3

ADJUSTMENTS

• Turn the power off when performing adjustments.

(1)  Adjusting the tone arm height

1

q

Lower the lifter lever.

w

Set the stylus on the record and check that the
tone arm is virtually parallel to the record’s
surface.

2

If not:

q

Set the tone arm back on the arm rest.

w

Move the lock lever in the opposite direction of the
arrow to unlock.

e

Move the height adjustment dial and adjust the height
so that the arm is virtually parallel to the record’s
surface.

r

Move the lock lever in the direction of the arrow to
lock the height.

1

Set both the anti-skating knob to “0”.

2

Move the tone arm.

• Lift the tone arm from the arm rest and move it over

the platter.

When moving the tone arm, be careful that the stylus
does not directly touch the platter or other parts.

For cartridges with detachable stylus covers, adjust
with the stylus cover removed.

3

Adjust the horizontal balance.

• Move the counterweight forward or backward so that

the tone arm is parallel to the platter’s surface when
the tone arm is released.

When adjusting the horizontal balance, be careful that
the stylus does not touch the slip mat or the main unit.

(2)  Stylus pressure and anti-skating adjustment

B

4

Set the tone arm back on the arm rest.

• Set the tone arm back on the arm rest.

230

115

230V

115V

5

Hold the counterweight with a
finger so that it does not move,
then turn the stylus pressure
adjustment ring so that the center
line on the back of the tone arm is
at “0”.

6

Turn the counterweight in the direction of the arrow
and set it for the proper stylus pressure for the
cartridge you are using.

When the counterweight is turned, the stylus pressure
adjustment ring also turns. Read the value on the
adjustment ring to set the proper stylus pressure.

7

Turn the anti-skating knob and set it so that the
value of the cartridge’s stylus pressure is lined up
with the reference line.

• This provides the proper anti-

skating force.

ANTI-S

K

A

T

IN

G

0

1

2

3

4

5 6 7

0

0.5

1

1.5

3

3.5

Summary of Contents for DP-DJ151











Reviews: