background image

 

 

 

Warranty Procedure 

End Users 
 
If your machine develops a problem: 
 
1.  Phone Demon for advice with the model and serial number to hand. 
2.  Describe fully the problem as best you can. 
3.  If the problem cannot be resolved over the phone then the machine can be booked in for 
repair and if the faults are covered by the warranty the repair will be carried out free of charge. 
4.  If you cannot bring the machine in for repair then we will despatch an engineer. If the fault 
is  covered  by  the  warranty  then  we  will  not  charge  for  labour  or  spares  used,  however  the 
transport charge will be payable weather or not the repair is warranty. 
 
 
Hire Centres and Dealers 
 
If your machine develops a problem: 
 
1.  Phone Demon for advice with the model and serial number to hand. 
2.  Describe fully the problem. 
3.  We will advise you on the best course of action, however if parts are required you must raise 
a purchase order number to cover the parts. When the parts are fitted they must be returned 
for examination before a credit note is issued. 
4.  If you are unable to repair the machine then we will despatch an engineer to carry out the 
repair. We will need a purchase order to cover the cost of transport to and from the site and for 
parts and labour if the repair is not covered under the warranty. 
5.  If required Demon will arrange for a carrier to collect a damaged machine, if the warranty 
claim is valid we will pay this cost, if not it will be charged to the customer. 
For parts warranty ring Demon and request a warranty claim form faxed to you. This form must 
accompany any returned parts. 
 
 
Notes:  
 
You will not invalidate the warranty by investigating faults and repairing them yourself providing 
you follow our advice. Hire Centres and Dealers are expected to carry out all repairs themselves 
with Demon crediting faulty parts upon receipt and inspection. 
Spare parts fitted to machines are guaranteed for 1 month only or the remainder of the war-
ranty period whichever is longer.  

 

 

Summary of Contents for HURRICANE D1 SALT WATER






















Reviews: