DEMAG DRF 200 Assembly Instructions Manual Download Page 31

Page: 31 / 52

5.8

Load bar

Ø20

Ø26

122,5

245

285

R16

Fig. 16

WARNING

Overload
Danger to life and limb due to an overload.
The maximum permissible safe working load is 270 kg for non-guided loads which are allowed to swing freely.

5.9

Connecting the electric equipment

Mains connection

First check to ensure that the voltage and frequency specified on the rating plate match your mains supply.

The protective conductor marked green/yellow in the supply line must be connected to the green/yellow earth ter‐

minal. If conductor lines are used to supply power, the protective earth conductor line must be specially marked. If

it is mounted on insulators, it is sufficient to mark the insulators.

Friction wheel travel drive

The motors are connected in star when they leave the factory. Connect the friction wheel travel drive in accord‐

ance with the wiring diagram.

214

5 44/120

914

Summary of Contents for DRF 200





















































Search results

Summary of Contents for DRF 200

Reviews:

Related manuals for DRF 200

Brands by name

Popular brands

DEMAG DRF 200, Assembly Instructions Manual

Search results

Summary of Contents for DRF 200

Reviews:

Related manuals for DRF 200

Brands by name

Popular brands