Delta Vivotek Supreme IP9165-HT-v2 User Manual Download Page 12

Page: 12 / 424

VIVOTEK

12 - User's Manual

7. Please visit VIVOTEK’s website to Install the "Shepherd” software utility. The program

will search for VIVOTEK Video Receivers, Video Servers or Network Cameras on the

same LAN.

Double-click on the camera’s MAC address to open a web console to the camera.

Browser

LAN

Shepherd

DI-

DO+

DI+

DO-

Switch

External Device

Dry contact and using camera’s DO+ to supply a relay.

Relay

External AC power

with Protected Earth

Summary of Contents for Vivotek Supreme IP9165-HT-v2







































































































































































































































































































































































































































Search results

Summary of Contents for Vivotek Supreme IP9165-HT-v2

Reviews:

Brands by name

Popular brands

Delta Vivotek Supreme IP9165-HT-v2, User Manual

Search results

Summary of Contents for Vivotek Supreme IP9165-HT-v2

Reviews:

Brands by name

Popular brands