background image

3- ENG

D26195

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

Improper operation or maintenance of this product could result in serious injury and
property damage. Read and understand all warnings and operation instructions before
using this equipment.

HAZARD

WARNING: Risk of explosion or fire

How To Prevent It

What Could Happen

It is normal for electrical contacts 

within

the motor and pressure switch

to spark.

If 

electrical 

sparks

from compressor

come into contact with flammable
vapors, they may ignite, causing fire or
explosion.

Restricting

any of the 

compressor

ventilation openings

will cause serious

overheating and 

could cause fire.

Unattended operation

of this product

could result in personal injury or
property damage. To reduce the risk of
fire, do not allow the compressor to
operate unattended.

Always 

operate the compressor in a

well

ventilated 

area free of combustible

materials, gasoline, or solvent vapors.

If spraying flammable materials, 

locate

compressor at least 20 feet away from
spray area.

An additional length of hose

may be required.

Store flammable materials in a secure
location away from compressor.

Never place objects against or on top
of compressor. Operate compressor

in

an open area 

at least 12 inches away

from

any

wall or obstruction

that would

restrict the flow of fresh air to  the
ventilation openings.
Operate compressor in a clean, dry well
ventilated area.

Do not operate unit

indoors or in any confined area.

Always remain in attendance

with the

product when it is operating.

Always disconnect electrical power by
moving pressure switch lever to the off
position and drain tank daily or after
each use.

Summary of Contents for Oil-Free 66-651



























Reviews: