background image

104437   Rev. A

Installation

Cartridge Installation

3

  

 

 

A.

B.

Turn off water supplies. Remove cover (1),

bonnet nuts (2) and test caps (3) from the 

rough-in body (4).

Place a bucket or small container over the front

of the valve body and slowly open the water

supplies to flush any debris from the supply

lines before installing the cartridge. Turn the

water supplies back off.

Rotate valve cartridge (1) so the words “HOT 

COLD” (2) appear on the top. Insert cartridge 

assembly into rough-in body. Make sure the key 

(3) on the cartridge is fully engaged with the slot 

in the brass body (4). Insert bonnet nut (5) on  

the cartridge and thread onto the body. Hand 

tighten securely. Slide o-ring (6) over cartridge 

and bonnet.A light coating of plumbers grease 

applied to o-rings may aid in assembly.

For the exceptions of back to back or reverse

installations (hot on right and cold on left) only:

Rotate valve cartridge (1) so “HOT COLD” (2) 

appears on the bottom.

Apply silicone lube to the three o-rings shown 

above to make the cartridge easier to install and 

remove from the rough-in body.

Install the cartridge making sure that the keys 

are fully engaged with the slot in the rough-in 

body (see step B).

Slide o-ring (4) and bonnet nut (3) over the 

cartridge and thread onto the rough-in body. 

Hand tighten securely.

Back to back Installation

Normal Installation  

(changes not required)

Reverse

Installation

Cold

Hot

1

2

3

4

2

3

1

2

3

4

5

3

4

2

4

3

1

1

6

Summary of Contents for MultiChoice T24 Series









Reviews: