Delta DVS-328 series User Manual Download Page 122

Page: 122 / 246

C h a p t e r 3 F e a t u r e d F u n c t i o n s

3 - 1 0 1

Login User Sessions

Item

Description

The unique session identifier

Type

The session types:



console



telnet



ssh



http



https

User

The name of the user who log in.

Peer-Address

The IP address to which the user log in.

3.11.3

Denial of Service

The Delta switch provides six types of denial of service (DoS) attacks for you to block and monitor attacks.
Please refer to the following table for description.

Denial of Service Configuration

Description

Factory default

Denial of Service SIP=DIP

Select one of the following radio buttons:



Disable:

This is the default setting.



Enable:

Packets that have a source IP (SIP) address equal to the destination IP

(DIP) address are dropped.

Disable

Denial of Service First Fragment

Select one of the following radio buttons:



Disable:

This is the default setting.



Enable:

Packets with a TCP header that is smaller than the configured minimum

TCP header size are dropped.

Disable

Denial of Service Min TCP Hdr Size

Specify the minimum TCP header size. Enter a value in the range of 0 to 255 bytes.

Denial of Service TCP Fragment

Select one of the following radio buttons:



Disable:

This is the default setting.



Enable:

Packets that have an IP fragment offset equal to 1 are dropped.

Disable

Denial of Service TCP Flag

Select one of the following radio buttons:



Disable:

This is the default setting.

Disable

Summary of Contents for DVS-328 series























































































































































































































































Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands

Delta DVS-328 series, User Manual

Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands