Delta DTH2450 Instruction Manual Download Page 10

10- ENG

A00521

7.

Turn water source on.
NOTE: 

Failure to do so could

cause damage to the pump.

8.

Start engine.

See Engine Owners

Manual for correct procedure.

NOTE: 

When engine rope is

pulled, pressure starts building in
the gun. If the engine does not
start after two pulls, pull the gun
trigger to relieve this pressure.

9.

Depress trigger on gun to start
water flow. NOTE: Stand on a
stable surface

and grip

gun/spray wand firmly with both
hands. Expect the gun to kick
when triggered.

10. Release trigger to stop water

flow.

11. Adjust nozzle spray for the task

being performed. See How To Use
Wand instructions in this section.

SHUTTING DOWN

1.

After each use,

if you have

applied chemicals, place chemical
hose into container of clean water
and draw clean water through
chemical injection system to rinse
system thoroughly.

NOTE:

Failure

to do so could cause damage to
the pump.

2.

Turn engine off.

See Engine

Owner’s Manual. 

NOTE: NEVER

turn the water off with the engine
running.

3.

Turn water source off.

4.

Pull trigger on spray gun

to

relieve any water pressure in hose
or spray gun.

5.

See Storage section

in this

manual for proper storage
procedures.

4.

Connect

water source to pump

inlet.

NOTE:

Water source must provide a

minimum of 5 gallons per minute at
20 PSI.

5.

Connect

high pressure hose to

pump outlet.

6.

If applying a chemical or cleaning
solution

, see How To Apply

Chemicals/Cleaning Solvents
instructions in this section.

STARTING

Prior to starting, refer to your engine
manual for proper starting procedure.

1.

In a well ventilated outdoor area

add fresh, high quality, unleaded
gasoline with a pump octane rating
of 86 or higher.  Do not overfill.
Wipe up spilled fuel before starting
the engine. Refer to  Engine
Owners Manual for correct
procedure.

2.

Check engine oil level.

See Engine

Owners Manual for correct
procedure. 

NOTE: There will be a

slight amount of oil in the engine
from factory testing.

3.

Verify the filter
screen

is in water

inlet of pump.

NOTE: 

Cone side

faces out.

High Pressure Hose

Water
Source

Filter Screen

Summary of Contents for DTH2450

















Reviews: