(4) Mounting dimensions
DOP-112MX / DOP-112WX
Unit: mm (inch)
Operating temperature: 0°C to 50°C (32°F to 122°F)
Storage temperature: -20°C to 60°C (-4°F to 140°F)
DOP-115MX / DOP-115WX
Operating temperature: 0°C to 50°C (32°F to 122°F)
Storage temperature: -20°C to 60°C (-4°F to 140°F)
(5) Installation and wiring
Precautions:
Incorrect installation may result in malfunction
To ensure the HMI is well ventilated, make sure there is sufficient space between the HMI and the
adjacent objects or walls.
This product should be used on a case / platform which conforms to enclosure Type 4X standard
(for indoor use only).
The maximum panel thickness for mounting must be no greater than 5 mm.
Installation steps:
Step 1:
Put the waterproof gasket into the HMI and then
insert the HMI into the panel cutout.
Step 2:
Place the fasteners into the slots and tighten
the screws until reaching the panel cutouts.
Step 3:
Tighten the screws with the torque less than
0.5 N-M / 0.7 N-M to avoid damage to the plastic
case.
Torque for DOP-112MX / 112WX / 115MX /
115WX: 6.17 lb-inch (0.7 N-M)
Step 4:
For heat dissipation, please keep a minimum
clearance of 60 mm on the rear of the HMI.
Wiring:
Type
Wire gauge (AWG)
Stripped length
Torque
Solid
24
–
12
7
–
8 mm
5 kg-cm (4.3 lb-in)
Stranded
24
–
12
7
–
8 mm
5 kg-cm (4.3 lb-in)
Please refer to the following diagram when wiring the power connector. The temperature
rating of the cable must be greater than 75°C (167°F).
(6) Hardware specifications
Model
DOP-112MX
DOP-112WX
DOP-115MX
DOP-115WX
D
is
pla
y
Panel type
12.1" TFT LCD (24-bit color)
15.1" TFT LCD (24-bit color)
Resolution
1024 x 768 pixels
Backlight
LED Back Light (half-life under room temperature 25°C > 50,000 hours)
*
1
Display range
245.76 mm x 184.32 mm
304.1 mm x 228.1 mm
Brightness
500 cd / m² (Typ.)
450 cd / m² (Typ.)
CPU
Dual 1GHz
Flash ROM
8GB
RAM
DDR3 1000MHz 1GB
Touchscreen
4-wire resistive touchscreen > 10,000,000 operated
Buzzer
Multi-Tone Frequency (2K – 4K Hz) / 85 dB
Network interface
100M bps x 1
1000M bps x 1
USB
1 Mini USB Ver 2.0; 1 USB Host Ver 2.0
SD
SD x 1
S
er
ia
l
co
m
m
u
nic
ati
on
po
rt
COM1
RS-232 (supporting flow control) / RS485
*2
COM2
RS-422 / RS485
*2
COM3
RS-232 (supporting flow control) / RS-485
*2
COM4
RS-422 / RS485
Auxiliary function key
N/A
Calendar
Built-in
Cooling method
Natural cooling
Approvals
CE / UL
(please use shielding network cable and magnetic ring with the filter of
300 ohm / 100 MHz)
Panel waterproof level
IP65 / NEMA4 / Type 4X for indoor use only
Operation voltage
*2
DC +24V (-15% to +15%) (please use an isolated power supply)
Supplied by Class 2 or SELV circuit (isolated from MAINS by double insulation)
Leakage current
500 V
AC
for 1 minute (between DC24V terminal and FG terminal)
Power consumption
*2
16.08 W (Max)
*3
21.12 W (Max)
*3
Backup battery
3V lithium battery CR2032 × 1
Backup battery life
About 3 years or more at 25°C
(subject to operating temperature and condition)
Operating temperature
0°C to 50°C (32°F to 122°F)
Storage temperature
-20°C to +60°C (-4°F to 140°F)
Operating environment
10% to 90% RH [0°C - 40°C], 10% to 55% RH [41°C - 50°C];
pollution degree: 2
Vibration resistance
Conforms to IEC61131-2: continuous vibration 5 Hz - 8.3 Hz with amplitude
3.5 mm; 8.3 Hz - 150 Hz with amplitude 1G
Shock resistance
Conforms to IEC60068-2-27:
11 ms, 15 G Peak, in X, Y, Z directions each for 6 times
Dimension
(W) x (H) x (D) mm
317.4 x 246.4 x 52.7
387.7 x 295.7 x 63.5
Mounting dimension
(W) x (H) mm
302.7 x 228.7
372.4 x 283.7
Weight
Approx. 2,110 g
Approx. 3,200 g
Note:
1. The half-life of the backlight is defined as the maximum luminance being reduced by 50% when the
maximum drive current is supplied to the HMI. The life of LED backlight shown here is estimated at the
room temperature of 25°C with ambient humidity.
2. The withstand voltage of the isolated power circuit is 1500V peak for 1 minute.
3. The HMI power consumption is the power consumed when the HMI is not connecting with other
peripheral devices. To ensure normal operation of the HMI, the recommended capacity of the power
supply is 1.5 to 2 times of the specified power consumption.
4. Isolated power supply is recommended.
5. For the DOPSoft programming software of the DOP-100 series and the user manual, you can
download them at http://www.delta.com.tw/ia.
6. DOP-100 series can be used with other industrial automation equipment. Please read through this
sheet carefully and install the product according to the instructions to avoid danger.
