background image

 WARNING:

*

Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding 

under an infant.

*

Failure to follow these warnings and the assembly instructions could result in serious injury or death. 

DO NOT use this crib if you cannot exactly follow the accompanying instructions.

*

To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to 

sleep, unless otherwise advised by your physician.

*Strangulation Hazard:

 STRINGS CAN CAUSE STRANGULATION! 

Do not

 place items with a string 

around a child's neck, such as hood strings or pacifier cords. 

Do not

 suspend strings over a crib or 

attach strings to toys.

*Strangulation Hazard:

 To help prevent strangulation tighten all fasteners. A child can trap parts of 

the body or clothing on loose fasteners.

*Strangulation Hazard:

 

Do not

 place crib near window 

or patio door  

where cords from blinds or 

drapes may strangle a child.

*Fall Hazard:

 When child is able to pull to a standing position, set mattress to lowest position and 

remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib 

has an adjustable mattress support. For the convenience of the parent when the baby is very small, the 

mattress support may be used in the highest position.  Important:  with the mattress support and 

mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches 

higher than the top surface of the mattress.  If it is not, lower the mattress support and the mattress to 

the next highest position.

*Fall Hazard:

 Stop using crib when child begins to climb out or reaches a height of 35in. (89cm),  

whichever occurs first. The child should be placed in a youth or regular bed. 

*

Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, 

or sharp edges before and after assembly and frequently during use.  Securely tighten loose bolts and 

other fasteners. 

Do not use crib

 if any parts are missing, damaged or broken.  Contact Delta 

Children's Products for replacement parts and instructional literature if needed.  Do not substitute parts.

*Follow warnings on 

all 

products in a crib.

*If refinishing, use a non-toxic finish specified for children's products.

*

Never

 use plastic shipping bags or other plastic film as mattress covers because they can cause 

suffocation.

*Infants can suffocate in gaps between crib sides and a mattress that is too small.

*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that 

every component is properly and securely in place.

*To avoid head injury, do not allow any child to play underneath the crib.

*

Never

 add an accessory such as a bassinet or changing table that extends over the sleeping area.

*

In Canada Only

 - Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it 

is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the 

mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or 

who is taller than 90 cm.

 CAUTION:

ANY MATTRESS USED IN THIS CRIB SHALL 

BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A 

THICKNESS NOT EXCEEDING 6 IN.

Summary of Contents for 7886

















Reviews: